AQUASCUD SYSTEM 420 WATERPROOFING MATERIAL
AQUASCUD SYSTEM 420 WATERPROOFING MATERIAL
Waterproofs old and new terraces.
Two-component flexible waterproofing product, with core curing technology for effective curing even under low temperature conditions and partially damp surfaces, ideal for waterproofing terraces, balconies and flat roofs.
information
PRODUCT APPLICATION
- Substrates in general, also lightened with expanded clay
- Waterproofing of flat roofs, balconies, terraces and sloped floors, with flooring already installed, with waterproofing surface that can remain exposed protected by coatings (tiles, concrete floors, green roofs, etc.)
BRAND
Volteco
PRODUCT TYPE
Waterproof Coating
ADVANTAGE
- Resistant to U.V. radiation
- For waterproofing without demolition.
- Fast drying even in low temperature conditions (all within 24 hours)
- Low environmental impact thanks to reduced CO₂ emissions, very low Volatile Organic Compound emissions (VOC), components obtained from recycling processes
PRODUCTION
Made in Italy
WORKABILITY TIME AT +20°C
20’
SURFACES
Excellent adhesion to all cement, masonry, ceramic and marble surfaces
CERTIFICATION
The product helps earning points for LEED certification
THICKNESS
3 mm
RESISTANCE AT BREAKING POINT
> 0.6 kN/m
APPEARANCE
Grey powder - white latex
SYSTEM
Flexible liquid systems
WATERTIGHTNESS (WATER PASSAGE WITH 60 KPA)
No passage (UNI EN 1928)
PACKAGING AND STORAGE
Aquascud 430 is supplied in 18 kg packages (12 kg in powder + 6 kg in liquid). The product must be stored in a dry place without being exposed to frost and heat (at a temperature between +5°c and +30°c) or direct exposure to the sun before being applied.
DOWNLOADS
↓ Bim Terrace Aquascud System 420+aquascud LINE
↓ Ds_aquascud system_ sealing of corner_199_en.pdf
↓ Ds_flat roof accessible to vehicular traffic - aquascud system_229_en.pdf
↓ Ds_aquascud system - expansion joint sealing_519_en.pdf
↓ Ds_connection between aquascud system on the sloped screed and amphibia 3000 grip on foundation wall_658_en.pdf
PREPARATION AND APPLICATION
PREPARING THE MIXTURE
Stir the liquid component in its container, then pour it into a bucket. Gradually add the aquascud powder component while continuing to stir; mix for 2÷3 minutes with a whip-fitted drill until the mixture is smooth and free of lumps. If necessary, it tolerates the addition of water up to maximum 4% of the liquid component, equal to about a glass per package.
FINISHING
Ceramics must be laid on aquascud system 430 after at least 2 days, with a large grout gap and c2-type adhesive (preferably with an s1 and s2 deformation class). Line grouting works must be carried out with cg2 class cement-based grouting mortars. Aquascud system 430 can be left exposed if subjected to occasional foot traffic.
PREPARING THE SURFACES
- Remove all dirt and any other material that could compromise adhesion of aquascud.
- Restore very irregular surfaces with flexomix 30 mortar (see the related technical data sheet).
- If the surfaces are old or dusty, apply profix 30 primer with a roller, a brush or by spray (see related technical data
Sheet).
- For substrates that are not completely dry but adequately cured, the surface relative humidity must not exceed 5% (Measured using a storch type electric hygrometer).
- If the substrate is partially soaked in water, with relative surface humidity between 5% and 10% (measured using a Storch type electric hygrometer), apply bi mortar ultra seal (see relevant technical data sheet).
PREPARATION OF INSTALLATION PARTS AND SET-UPS
- Drains prepare the connections to the drains by using the relative drain manifold
- Gutter along the external perimeter, set up the aquascud LINE draining gutter profile and relative special
Pieces (see relative data sheet) to finish and protect the tiled edge
- Joints any deformation joints (expansion and contraction/splitting) and construction joints on the surface must be Covered by means of garvo joint cover strips (see relevant technical data sheet); in case of structural joints, use bi Flex system (see relevant technical data sheet)
- Elastic reinforcement prepare the aquascud basic membrane, pre-cut to the required measurements, So that it can be applied with the first coat of waterproofing mixture
- Corners and connections in case of insulation joints, fill all wall/floor corners by means of aquascud Join (see relevant technical data sheet) staff bead, placing the rubber-coated part in contact with the surface using Aquascud sealing material. Alternatively, it is possible to use the aquascud join bt adhesive strip (see relevant Technical data sheet) laid on a cured aquascud layer. At low-height situations use aquascud join bt or, Alternatively, bi mastic adhesive mastic (see relevant technical data sheet)
APPLICATION
Apply the first thick layer of aquascud 420 on the surface, a minimum thickness of 1÷1.5 mm using a special Volteco 3.5 mm notched float and/or the volteco notched or roller squeegee, making sure the product Penetrates well into the substrate and covers the surface completely (average consumption: 2-2.5 kg/m² depending on The flatness of the surface). Place the aquascud basic membrane on the first coat of mixture in the following manner: proceed in sectors, Immediately laying aquascud basic out on the fresh aquascud 420 mixture, making it adhere uniformly to the Surface by pressing with the volteco needle roller.
Aquascud basic membrane becomes darker when it is rolled on. This indicates correct application and proper Impregnation and adhesion. Overlap the edges of the aquascud basic membrane by at least 10 cm and weld them together with the Aquascud mixture. Where the horizontal and vertical surfaces join, make sure the aquascud basic membrane adheres to the Horizontal edge of the previously laid aquascud join joint band. Never fold aquascud basic vertically, always join it to the aquascud join joint band.
The aquascud basic membrane must be interrupted in the centre line of the tape with garvo or bi flex system At the joints treated. If there is an aquascud LINE gutter profile along the perimeter, overlap aquascud basic by at least 6 cm over The profile anchoring flap.
Wait at least 2 hours (ambient temperature +20°c; ambient humidity 60%) before using notched trowel 3.5 mm Or notched squeegee to apply a second layer, at least 1 mm thick, of the aquascud 420 mixture (average Consumption 1.75÷2 kg/m²), being careful to evenly cover the aquascud basic membrane. When fresh, smooth with rounded plastering trowel. It is recommended to apply the second layer of aquascud 420 only when the previous one is completely dry and Hardened. For applications on balconies or on small surfaces (less than approximately 4 m²), it is possible to omit the use of the Aquascud basic membrane. Always apply the aquascud basic membrane on a substrate with marked cracks.







