Watco V2100 System Enamel Spray Paint by Rust-Oleum
V2100 SYSTEM ENAMEL SPRAY PAINT BY RUST-OLEUM
V2100 SYSTEM ENAMEL SPRAY PAINT BY RUST-OLEUM
Rust-Oleum High Performance V2100 System Rust Preventive Enamel Spray Paint is ideal for industrial spray painting projects.
This heavy-duty spray paint for metal provides a professional finish that resists chipping, cracking and peeling in harsh environments.The advanced formula in this aerosol provides the best-possible corrosion protection with easy, one-coat coverage and long-lasting color, gloss and durability.
INFORMATION
BRAND
Watco
PRODUCT TYPE
Paint
COLLECTION
Enamel
AVAILABLE COLORS
9
FEATURES AND BENEFITS OF V2100 SYSTEM ENAMEL SPRAY PAINT
- Withstands heat up to 200°F
- Dries to a touch in 20 minutes
- High-output tip covers 50% faster
- Can also be used as a touch-up paint
- Ideal for metal, steel, masonry and wood surfaces
- Meets USDA requirements for incidental food contact; accepted for use in federally registered Canadian food facilities; VOC-compliant nationwide.
COVERAGE
12-20 sq ft
SKU
V2124838
CURE TIME
Tack free in 20mins
DOWNLOADS
↓ SDS V2143838_V2100_Yellow.pdf
↓ SDS V2155838_V2100_Orange.pdf
↓ SDS V2183838_V2100_Light Gray.pdf
↓ SDS V2187838_V2100_Dark Gray.pdf
↓ SDS V2192838_V2100_White.pdf
↓ TDS V2100_System_Enamels.pdf
↓ SDS V2124838_V2100_Blue.pdf
↓ SDS V2163838_V2100_Red.pdf
↓ SDS V2171838_V2100_Tan.pdf
↓ SDS V2179838_V2100_Black.pdf
SUITABLE FOR
- Steel
- Wood
- Metal
- Masonry
PRIMER SUGGESTIONS
Not required, but for best performance, use with V2182838 Gray Primer
RECOAT TIME
Within 1 hour or after 24 hours depending on temperature
FINISH
- Smooth
- Gloss Finish
USAGE INTERIOR/EXTERIOR
- Interior
- Exterior
HOW TO APPLY
APPLICATION
Use when temperature is above 50°F (10°C) and humidity is below 85% to ensure proper drying. Surface temperature must be between 50-100°F (10-38°C). Use a primer on bare or rusted surfaces. Protect surrounding surfaces from overspray. Overspray can carry a significant distance. Shake can for one minute after mixing ball is heard. Hold can 10-14 inches from surface. Apply several light coats a few minutes apart to avoid drips and runs.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a solvent such as mineral spirits. Do not insert any object into can valve opening.
DRY & RECOAT TIMES
Recoat within 1 hour or after 24 hours. Allow more time in cooler temperatures.
CLEAN-UP
Wipe off tip before storing. Clean-up wet paint with xylene or mineral spirits. Properly discard empty container. Do not burn or place in trash compactor. Empty container can be recycled.
SURFACE PREPARATION - PREVIOUSLY COATED
Previously coated surfaces must be sound and in good condition. Smooth, hard, or glossy finishes should be scarified by sanding to create a surface profile.
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with a commercial detergent, or other suitable cleaning method. Rinse with fresh water and allow to thoroughly dry. Remove loose paint and rust with a wire brush or sandpaper. Previously coated surfaces must be sound and in good condition. Smooth, hard, or glossy finishes should be scarified by sanding to create a surface profile.
SURFACE PREPARATION - STEEL
Hand tool (SSPC-SP-2) or power tool (SSPC-SP-3) clean to remove loose rust, mill scale, and deteriorated previous coatings.
COLORS
COLORS
