Kilz Kilz® Masonry, Stucco & Brick Flat Paint
KILZ® MASONRY, STUCCO & BRICK FLAT PAINT
KILZ® MASONRY, STUCCO & BRICK FLAT PAINT
KILZ® Masonry, Stucco & Brick Flat paint is a high-quality, acrylic latex paint with excellent hiding properties.
This interior/exterior, self-priming, mildew resistant finish also provides excellent adhesion and water repellency on properly prepared, smooth, rough and textured masonry, stucco and brick surfaces
INFORMATION
BRAND
Kilz
PRODUCT TYPE
Paint Interior
COVERAGE
250-400 Sq. Ft./Gal.
ROLLER - SMOOTH
3/8" - 1/2" nap
BRUSH
Nylon / Polyester
RESIN TYPE
Acrylic Latex
COLLECTION
Kilz®
T 250 SQ. FT./GAL. (WET)
6.4 Mils
VOC
<50g/L
SHEEN @ 85°
0-6
AT 250 SQ. FT./GAL. (DRY)
2.0 Mils
INT/EXT
Yes
% SOLIDS BY VOLUME
30%
% SOLIDS BY WEIGHT
44.5%
BEST FOR USE ON
Ideal for properly prepared, smooth, rough and textured masonry, stucco and brick surfaces, as well as adjacent wood and metal. Do not use on horizontal surfaces subject to foot traffic.
VISCOSITY
95-105 KU
WEIGHT / GALLON (LBS)
10.7
FLASHPOINT
No
AT 400 SQ. FT./GAL. (WET)
4.0 Mils
AT 400 SQ. FT./GAL. (DRY)
1.2 Mils
DETAIL
This water-based formula is designed to accentuate all textured surfaces while achieving a natural look. It is alkali-resistant up to pH 12.0, easy to apply, and cleans up with soap and water.
FINISHES
Available in Gray, Tan, and White. Flat Mildew-Resistant Finish.
THICK
Thick excellent coverage
SURFACE
Minimal surface preparation required
DETAIL
DRY TIME AT 77°F (25°C), 50% RH
- Dries to touch in 1 hours.
- Wait 2-4 hours before recoat.
- After two weeks, cured paint film may be cleaned with a mild, non-abrasive liquid detergent.
- Additional dry time may be needed in cooler temperatures and higher humidity. Premature heavy traffic may affect film integrity.
CLEAN UP & DISPOSAL
- Clean equipment and paint spatters with warm, soapy water.
- If spilled, contain material and remove with an inert absorbent.
- Dispose of contaminated absorbent, container and unused product in accordance with all current governmental regulations.
- Do not dispose of this product down a drain. For recycling or disposal information contact your local household refuse collection service.
APPLICATION
- Maintain a wet edge to avoid lap marks. Do not re-spread or re-work paint.
- Coverage: rough surfaces: 250-300 sq. Ft; smooth surface 400 sq. Ft.
- Do not dilute. Intermix all cans of same product to ensure color uniformity. Stir paint before and occasionally during application.
- For best results, apply when air and surface temperatures are between 50-90°F. Do not use if rain or heavy dew is expected within 24 hours.
- Apply using a high quality 3/4"-1" nap roller (rough surfaces) or 3/8"-1/2" nap roller (smooth surfaces), nylon/polyester brush or airless sprayer (.015"-.021" spray tip, 60 mesh filter). Apply a second coat, if necessary.
PRODUCT USAGE - SURFACE PREPARATION
The following steps and products are required:
- Allow new stucco and masonry to cure for 30 days before painting.
- Remove all loose, peeling paint. Power wash to remove chalk. Remove dirt, grease and mildew stains with KILZ Concrete & Masonry Cleaner & Degreaser.
- On galvanized metal, use a diluted solution of KILZ Concrete & Masonry Cleaner & Etcher to prepare the surface. Rinse thoroughly and allow a minimum of 24 hours to dry.
- Cracks and gaps wider than 1/16" should be routed open, dusted and patched with a quality patching compound. Use an acrylic caulk around windows, doors and trim. Scuff sand glossy surfaces.
- If chalk remains on the surface, prime with a KILZ Premium Primer. Prime all patched areas as well as adjacent wood and metal surfaces. If previously sealed or coated, check manufacturer’s specifications before painting.
WARRANTY - LIMITED WARRANTY
For one year from the date of purchase, Masterchem Industries LLC warrants to the original residential consumer purchaser (1) that the product meets Masterchem Industries LLC’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. In the event that this product proves to be defective within one year from the date of purchase, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty is not transferable.
This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. For warranty service, call: 1-866-774-6371, or email: [email protected]. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
