Kilz® Decorative Concrete Coating
KILZ® DECORATIVE CONCRETE COATING
KILZ® DECORATIVE CONCRETE COATING
KILZ® Decorative Concrete Coating is ideal for Interior/Exterior surfaces such as porous concrete, masonry, stone pavers and brick. Ideal for garages, driveways, walkways, patios, porches and pool decks.
DO NOT use on vertical surfaces or areas subject to hydrostatic pressure. NOT for industrial use or areas subject to forklifts. Surfaces may become slippery when wet.
Use caution when walking on surface when moisture is present. Available in Tan and Gray
INFORMATION
BRAND
Kilz
PRODUCT TYPE
Concrete Coating
ROLLER - SMOOTH
1/4" Adhesive Roller
% SOLIDS BY VOLUME
39%
COVERAGE
40-60 Sq. Ft./Gal.
INT/EXT
Int/Ext
FINISH
Available in Tan and Gray Base. Textured, Slip-Resistant Finish.
DRY TIME AT 77°F (25°C), 50% RH
- Dries to touch in 1 hours.
- Wait 3-4 hours before recoat.
- Premature heavy traffic will cause paint failure requiring spot recoating.
- Wait at least 30 days before cleaning/rinsing with a cleaner.
- Additional dry time may be needed in cooler temperatures and higher humidity. Premature heavy traffic may affect film integrity.
- The floor may be subjected to light foot traffic after 24 hours. Allow 72 hours before subjecting surface to automotive tires, heavy foot traffic or repositioning furniture.
CLEAN UP
Clean all tools and equipment with soap and clean water.
2 COATS AT 40 SQ. FT./GAL. (WET)
40 Mils
2 COATS AT 40 SQ. FT./GAL. (DRY)
16 Mils
2 COATS AT 60 SQ. FT./GAL. (WET)
27 Mils
2 COATS AT 60 SQ. FT./GAL. (DRY)
11 Mils
VOC
<50 g/L
BRUSH
Synthetic
DISPOSAL
Do not dispose of this product down a drain. For recycling or disposal information contact your local household refuse collection service.
BEST FOR USE ON
Ideal for Interior/Exterior surfaces such as porous concrete, masonry, stone pavers and brick. Ideal for garage floors, driveways, walkways, patios, porches and pool decks. DO NOT use on vertical surfaces or areas subject to hydrostatic pressure. NOT for industrial use or areas subject to forklifts.
% SOLIDS BY WEIGHT
54%
WEIGHT / GALLON (LBS)
11
SURFACE PREPARATION†
The following steps and products are required:
- All surfaces must be clean, sound, dry and free of any dirt, oil, and grease.
- Uncoated Concrete or Masonry Surfaces: Allow new surfaces to cure 30 days. Clean and etch surface using a product such as a muriatic acid etcher (read and follow all manufacturer's label directions) to achieve a textured profile similar to 150 grit sandpaper.
- Previously Coated Surfaces: If surface is in sound condition, use a product to clean and prepare the surface. If the coating is failing or peeling, use a paint stripper to remove old coating or scrape/sand down to a sound concrete surface. Scuff sand glossy surfaces. Clean and spot etch any exposed concrete. Remove all dust with a damp cloth, allow to dry.
SHEEN @ 85°
<5
GLOSS @ 60°
<5
RESIN TYPE
Acrylic
WARRANTY
Limited Warranty
DETAIL
APPLICATION
- Do Not Thin.
- Intermix all cans of same product to ensure color uniformity. Stir before applying.
- Do not apply in extreme weather conditions. Use product when air temperature is between 50-90° f. Do not apply in direct sunlight.
-For hairline cracks up to 1/8", fill in with coating using a nylon/polyester brush and allow to dry completely prior to roller application.
- Apply a product such as KILZ® Concrete & Masonry Bonding Primer to increase adhesion of topcoat to the surface.
-Apply a first coat using a 1/4" adhesive roller cover, or nylon/polyester brush. Note: The first coat will act as the base coat and it will not completely cover the surface by design. Avoid over application on the first coat.
- An annual touch-up may be required in areas subject to high traffic.
- Allow first coat to dry before applying the second coat using the same method.
-Pour directly from the container onto the surface or apply using a roller tray.
- While 2 coats are necessary, additional coats may help hide previous surface imperfections or cover over dark colors.
- For large projects, consider using a texture sprayer with a 4mm tip. Spray in 4' by 4' sections and back roll with an adhesive roller cover.
- Apply in 4' by 4' sections. Begin with the roller in the center of the section and roll outwards in random directions. Avoid regular patterns and knock down hard edges using the roller.
