Kilz Kilz® Porch & Patio Floor Paint
KILZ® PORCH & PATIO FLOOR PAINT
KILZ® PORCH & PATIO FLOOR PAINT
KILZ® Porch and Patio Floor Paint is a 100% acrylic latex product providing a durable, long-lasting finish that is ideal for both interior and exterior applications. This product will create a mildew resistant finish that resists scuffing, fading, cracking and peeling.
Ideal for wood and concrete porches, floors, decks, basements, patios, siding, trim, furniture and trellises. May be applied over properly prepared, previously-painted or primed surfaces. Not for use on areas subject to automotive tires. For residential applications only. CAUTION! Sealed surfaces may become slippery when wet. Use caution when walking on surface when moisture is present.
INFORMATION
BRAND
Kilz
PRODUCT TYPE
Floor Paint
RESIN TYPE
100% Acrylic Latex
COVERAGE
200-400 Sq. Ft./Gal.
VOC
<50g/L
FINISH
Available in Silver Gray and Slate Gray. Mildew-Resistant Low-Luster Finish.
ENVIRONMENT
- Interior
- Exterior
BRUSH
Nylon / Polyester Blend
ROLLER - SMOOTH
3/8" - 1/2" nap
AT 200 SQ. FT./GAL.
- Wet : 8.0 Mils
- Dry : 2.9 Mils
AT 400 SQ. FT./GAL.
- Wet : 4.0 Mils
- Dry : 1.4 Mils
% SOLIDS BY VOLUME
35%
% SOLIDS BY WEIGHT
46%
DRY TIME AT 77°F (25°C), 50% RH
- Dries to touch in 1 hours.
- Wait 4-6 hours before recoat.
- Dry paint film provides a mildew resistant finish.
- Additional dry time may be needed in cooler temperatures and higher humidity. Premature heavy traffic may affect film integrity.
- Allow 72 hours before subjecting to normal use. After 4 weeks, cured paint film may be cleaned with a mild, non-abrasive liquid detergent.
BEST FOR USE ON
Ideal for porches, floors, decks, basements, patios, siding, trim, furniture and trellises. May be applied over properly prepared, previously-painted or primed surfaces. Not for use on areas subject to automotive tires.
WEIGHT / GALLON (LBS)
10.0
VISCOSITY
90-100 KU
CLEAN UP & DISPOSAL
- Clean equipment and paint spatters with warm, soapy water.
- Do not dispose of this product down a drain. For recycling or disposal information contact your local household refuse collection service.
- If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current governmental regulations.
WARRANTY
Limited Warranty
FLASHPOINT
N/A
CLEAN UP
Clean all tools and equipment with clean water. For disposal of empty containers and unused product, contact your household refuse collection service
SHEEN @ 60°
5-15
DOWNLOADS
↓ Technical Data Sheet
DETAIL
APPLICATION
- For best results, apply when air and surface temperatures are between 50-90°F.
- COVERAGE: Rough surfaces: 200-300 sq. ft.; Smooth surface 300-400 sq. ft.
- Stir paint occasionally. When working with more than one can of the same product, intermix to ensure color uniformity.
- Use a high quality 3/8"-1/2" nap roller cover, nylon/polyester brush or an airless sprayer (.015"-.019" spray tip, 60 mesh filter). Spread rates may vary depending on the surface texture, porosity and application method. Apply second coat in the opposite direction of the first. Do not dilute if using a roller or brush; however, if using a sprayer and thinning is required, dilute with water at a rate of no more than 1/2 pint per gallon. Certain colors may require more than one coat to achieve complete hide and coverage.
SURFACE PREPARATION†
The following steps and products are required:
- All surfaces must be clean, sound, dry and free of any dirt, oil and grease. Remove mildew stains with a mildew stainremoving product such as a wood cleaner and brightener.
- Scuff sand any glossy surfaces. If making repairs, use stainless steel or galvanized nails to prevent nail staining. Countersink nail heads, repair imperfections and sand smooth. Remove all dust with a damp cloth, allow to dry.
- New or Weathered Wood: Prepare surface with a wood cleaner and brightener. Lightly sand to remove remaining wood fibers/ fuzz. Prime with KILZ 3 Premium Primer.
- Painted Wood Surfaces: To strip an old coating, use a wood stain & finish stripper, then neutralize with a wood cleaner and brightener. For optimal adhesion, apply KILZ 3 Premium Primer before applying topcoat.
- Uncoated Concrete or Masonry Surfaces: Allow new surfaces to cure 30 days. Prepare surface with a concrete and masonry cleaner and etcher. Then prime using KILZ Concrete & Masonry Bonding Primer.
- Painted Concrete or Masonry Surfaces: To clean a painted surface in sound condition, use a concrete and masonry cleaner and degreaser. To strip an old coating, use a concrete and masonry paint stripper. Use a concrete and masonry cleaner and etcher to etch all exposed concrete, followed by KILZ Concrete & Masonry Bonding Primer before applying topcoat.
