Volteco Plastivo 180 Waterproof Coating

Tue Nov 05, 2024Waterproofing MaterialsConstructionCementVolteco, S.p.a.

PLASTIVO 180 WATERPROOF COATING

PLASTIVO 180 WATERPROOF COATING

Flexible Liquid Systems

Two-component, thixotropic and flexible modified polymer waterproof coating with core curing technology for effective curing even under low temperature conditions and partially damp surfaces.

information

ADVANTAGE

- Suitable for contact with drinking water
- Effective curing on even partially moist substrates
- Anticarbonation protection with ”barrier” function
- Fast curing allowing for short waiting times between the first and second coat and subsequent tiling, even under low temperature conditions (all in 24 hours)

BRAND

Volteco

PRODUCT TYPE

Waterproof Coating

MATERIAL

Cement

APPEARANCE

Grey Powder - White Latex

CONSUMPTION AND YIELD

÷3.5 kg/m² depending on the roughness of the surface.

SPRAYED APPLICATION

The product can also be applied with a pneumatic pump or plastering machine with levelling lance, taking care to apply a certain amount of pressure with a spatula until a compact surface is obtained (for further information contact Volteco's Technical Service).

PRODUCTION

Made in Italy

THICKNESS

3.5 mm & 2 mm

SPECIFIC WEIGHT

> 1.7 kg/l

WORKING TEMPERATURE

-5°C to +50°C

WORKABILITY TIME AT +20°C

20’

PACKAGING AND STORAGE

-Plastivo 180 is supplied in 20 kg packages (15 kg in powder + 5 kg in liquid). -The product must be stored in a dry place without being exposed to frost and heat (maximum temperature: 40°c) or direct exposure to the sun before being applied.

MAXIMUM AGGREGATE SIZE

0.7 mm

LIQUID/POWDER MIXING RATIO

33/100

FINISHING

-When applied indoors, it is recommended to coat the walls with the macroporous CALIBRO (see relative data sheet) as an anti-condensation layer. -It is also possible to complete the finish with X-LIME (see relative data sheet). -Depending on the intended use, the product can be finished either by painting with CRYSTAL POOL or with BI MORTAR RASO SEAL cement-based coating (see method and stratigraphy in the relevant technical data sheets) or with ceramic. -Ceramics must be laid with a large grout gap and C2-type adhesive (preferably with an S1 and S2 deformation class). -Line grouting works must be carried out with CG2 class cement-based grouting mortars.

FLEXONET OR XNET REINFORCEMENT MESH

-To improve elastic performance, in case of application in positive pressure (ex. crazing with dynamic behaviour, in roof top pools and structures that are potentially subject to cracking), it is advisable to place the FLEXONET or XNET (see the relative technical data sheets) mesh “fresh on fresh” on the 1st coat, pressing it down with a metal spatula until it is completely embedded. -The edges of adjacent sheets must overlap by 10 cm. -At the connection points between horizontal and vertical surfaces, and in any case at the BI FLEX System placed in the construction joints and joints, interrupt the mesh by overlapping it at the edge of the tape.

CURING

-When waterproofing foundation walls, let it cure for at least 16 hours after application before backfilling. -When coating the waterproofing with any type of protective layer or finish (ceramic coating, protective screed, plaster, cement-based levelling compound, plastic drainage, etc.), let it cure at least 16 hours after application. -With low temperatures till +5°C wait almost 24 hours. -When waterproofing structures intended to contain water, allow a curing phase of at least 3 days once the product is applied. -When used in contact with drinking water, wash the surfaces with running water before filling the container. -The curing times can be longer in the presence of a low temperature, high humidity or premature contact with water.

APPLICATION

For negative/positive hydrostatic pressure waterproofing of wall surfaces or concrete, affected by slight settlements and/or movements. Particularly suitable for :

- Balconies
- Substrates in general, also lightened
- Slabs and structures exposed to contact with water
- Reinforced concrete foundation walls of underground premises
- Roofs and screeds temporarily waterproof awaiting definitive works

- Protection of reinforced concrete surfaces with inadequate concrete cover thickness
- Ledges, concrete gutters, flower boxes (set-up anti-root protection beforehand) and wells
- Tanks, canals, swimming pools and structures designed to contain water, including drinking water
- All indoor surfaces such as kitchens, bathrooms and showers even if made of gypsum board or fibre concrete
- Protection of concrete from CO₂ penetration, contact with sea water, de-icing salts, aggressive atmosphere, etc.