Watco Floors Concrex Epoxy Repair Mortar Standard Plaster

Wed Dec 18, 2024PlastersConstructionWatco Industrial Flooring, Inc.

CONCREX EPOXY REPAIR MORTAR STANDARD PLASTER

CONCREX EPOXY REPAIR MORTAR STANDARD PLASTER

Use Concrex® Epoxy Repair Mortar to repair, reinforce and protect concrete floors. It cures to a granite-hard finish that is impervious and non-dusting.

INFORMATION

SIZE

- 20lb
- 50lb

BRAND

Watco Floor

PRODUCT TYPE

Plaster

SUITABLE FOR

Eroded or damaged concrete, bay edges, broken steps, sidewalks

SKU

A100015

POT LIFE

1/2 to 1 hours

PRODUCTION

Made in United States

APPLICATIONS AND SCREEDING

Tack Coat is essential to use as a primer for shallow applications and screeding

EASY TO APPLY

Easy to apply. Concrex takes heavy traffic after 12-16 hours at 60°-70°F

CURING TIME (HOURS)

Light traffic 3-6 hr

APPLY IN MINUTE

Minimal prep time saves labor costs; mix and apply in minutes

THICKNESS

Virtually indestructible 8 times stronger than concrete. Full strength achieved at 5mm thickness

COLORS

PRIMER REQUIRED

Yes - Tack Coat

USAGE INTERIOR/EXTERIOR

Interior or Exterior

PROPERTIES

Incredibly tough granite hard finish, chemical resistant, can be feather-edged to 2in depth (full strength is achieved at ¼in)

PRIMING

Tack Coat adhesive primer is recommended when applying Concrex® as a thin section screed or when applying to smooth, non-porous or metal surfaces.

COVERAGE

Approximately 9 sq. ft. per 20 lb. kit at 1/4" thick or 23 sq. ft. per 50 lb. kit at 1/4" thick

DOWNLOADS

↓ TDS Concrex Line.pdf
↓ SDS A070209 Concrex Standard 20lb Kit Black.pdf
↓ SDS A070212 Concrex Standard 50lb Kit Black.pdf
↓ SDS A070507 Concrex Standard 20lb Silver Gray Kit.pdf
↓ SDS A070510 Concrex Standard 50lb Silver Gray Kit.pdf
↓ SDS A070808 Concrex Standard 20lb Kit Tile Red.pdf
↓ SDS A070811 Concrex Standard 50lb Kit Tile Red.pdf
↓ SDS A100015 Concrex Standard 20lb Navy Gray Kit.pdf
↓ SDS A100016 Concrex Standard 50lb Navy Gray Kit.pdf

SURFACE PREPARATION

Surfaces should be clean, dry and free of all loose material. Wire brushing or sweeping is generally sufficient. If needed, wash with Bio-D Floor Degreaser and Cleaner or a suitable degreaser or detergent solution, to remove grease and oil. Rinse and allow to dry.

MIXING

Concrex® should be stored at an ambient temperature above 50°F for approximately 8 hours prior to use. Do not use material if air and surface temperatures are below 50°F. Each pack of Concrex contains aggregate pre-blended with resin and the curing agent. Do not mix inside the plastic bucket. Wearing protective gloves, tip the aggregate on to a mixing tray or board. Shake the containers of curing agent thoroughly until the liquid is a uniform color.

Form the aggregate into a mound and leave a small hole in the middle. Empty the curing agent into the hole, ensuring the container is completely drained. Carefully mix the aggregate with the curing agent using a trowel until a smooth mortar is obtained. This will take several minutes. The more thorough the mixing, the "wetter", smoother and more manageable the mix becomes. Alternatively, you can knead the mixture by hand, but you must wear suitable gloves. It is important to mix thoroughly until you achieve a consistent color.

T +1 855 6276350

[email protected]

Watco Industrial Flooring, Inc.

https://www.watcofloors.com

11 E Hawthorn Pkwy, Vernon Hills, IL 60061, United States