Watco Liquid Waterproofer Paint
LIQUID WATERPROOFER PAINT
LIQUID WATERPROOFER PAINT
SKU : B650049
Liquid Waterproofer Coating Is The Perfect Solution For Re-Surfacing And Damp-Proofing Basements, Workshops, Storerooms, Balconies, Walkways, Roofs, Fountains, Storage Tanks, Swimming Pools And More! Excellent For Use As A Waterproof Floor Coating As…
Liquid Waterproofer Coating is the perfect solution for re-surfacing and damp-proofing basements, workshops, storerooms, balconies, walkways, roofs, fountains, storage tanks, swimming pools and more! Excellent for use as a waterproof floor coating as well as a waterproof wall coating.
information
SUITABLE FOR
- Concrete
- Brick
- Masonry
BRAND
Watco
PRODUCT TYPE
Paint
FINISH
- Matte
- Textured
DOWNLOADS
↓ Data Sheet
↓ SDS B650049
PRACTICAL COVERAGE
Approximately 80 sq.ft per kit at 60 mils.
RECOMMENDED NUMBER OF COATS
2
COVERAGE
Approximately 81 sq. ft. per 55 lb. kit at 80 mil
CURING TIME (HOURS)
Light traffic: approximately 16 hr. in 70°F, heavy traffic after 3 days, full chemical curing over 7 days
VOLATILE ORGANIC COMPOUNDS
<50 g/l
SHELF LIFE
1 year
CLEAN UP
Clean up equipment immediately with water.
MIXING RATIO
22.5 pounds of power per 1 gallon of latex.
FULL CHEMICAL RESISTANCE
7 days
DRY TIMES
at 70-80°F (21-27°C) and 50% Rel. Hum. Light foot traffic 16 hours. Normal service 24-48 hours. Heavy traffic 72 hours
RECOAT
12-24 hours;Do not exceed 24 hours
POT LIFE
1 year
INDUCTION PERIOD
None
USAGE INTERIOR/EXTERIOR
Exterior
FLASHPOINT
Liquid component: >200°F
HOW TO APPLY
APPLICATION
The first coat can be applied while the surface is still damp but free from standing water. Use a medium hard short bristled brush or roller. The application thickness should be no more than 60 mil and no less than 20 mil per coat. The second coat may be applied as soon as the first is cured, normally 12-24 hours. For general flooring applications the total film thickness should be between 40-120 mil. To withstand 10 psi hydrostatic pressure the coating thickness should be a minimum of 80 mil for waterproofing. This should be applied in 2 coats (2 x 40 mil). A spiked roller should be used to release air and help even out the surface.
COVERAGE
Approximately 81 sq. ft. per kit at 80 mil.
POT LIFE
2 hours at 50°F, 1.5 hours at 70°F, 30 minutes at 85°F
SURFACE PREPARATION
The concrete surface must be clean, dry and free of loose material. New concrete should be allowed to cure for 28 days prior to coating. Remove oil, dirt, grease and other chemical contaminants by cleaning with detergent or other suitable cleaner. Rinse thoroughly. Use Cemtetch® to remove unsound laitance and create a proper surface profile to the concrete. Rinse thoroughly. Remove excess water by squeegee. The concrete surface must be damp at the time of application.
CURING TIME
At 70°F, a floor treated with Liquid Waterproofer can take light traffic after approximately 16 hours and heavy traffic after 3 days. Full chemical airing is achieved over 7 days. It is at this point the coating will resist permanent water pressure.
MIXING
Place the powder into an empty bucket and pour in approximately three quarters of the liquid component, mix using a slow speed drill and paddle mixer. Mix for approximately 3 minutes until a lump free, creamy consistency is achieved. Add the remaining liquid and mix thoroughly.