Watco Safety Coat Standard Paint
SAFETY COAT STANDARD PAINT
SAFETY COAT STANDARD PAINT
Safety Coat Standard is a uniquely formulated, skid-resistant epoxy floor coating that uses a special aggregate suspended in the liquid, allowing the coating to dry to an evenly textured, slip-resistant surface.
It provides a more attractive and easier-to-clean finish than conventional gritty paint. It is suitable as an interior coating for concrete or wood and can be used on all potentially slippery, concrete floors in heavy wear areas.
INFORMATION
PRODUCTION
Made in United States
BRAND
Watco
PRODUCT TYPE
Paint
USAGE INTERIOR/EXTERIOR
Interior
COLLECTION
Safety
SKU
C240502
USE
- Stairs
- Ramps
- Platforms
- Great for floors
APPLIED
Easily applied by a roller and paint brush to cut in the walls
RECOAT TIME
4-6 Hours
POT LIFE
2 hours at 60-70°F
CLEAN
Easy to clean with a dry dust mop or wet floor mop
SUITABLE FOR
- Wood
- Concrete
- Existing Well Bonded Paint
CURING TIME (HOURS)
12 Hours in 60-70°F
COVERS APPROXIMATELY
240 sq. ft. per kit
PRIMER REQUIRED
Not usually, but Powerfloat Base Coat may be needed for very smooth surfaces
BASE
This non-slip, water-based epoxy floor coating contains fine, slip resistant particles embedded in a tough epoxy resin coating
COLORS
- Blue
- Green
- Tile Red
- Mid Gray
- Silver Gray
FEATURES AND BENEFITS OF SAFETY COAT STANDARD FLOOR COATING
- Hard wearing
- Can withstand forklift traffic
- Ready for traffic in 12 hours
- Extremely durable & chemical resistant
- Non-flammable, virtually solvent free & odorless formula
DOWNLOADS
↓ Data Sheet
↓ SDS C240401 safety-coat-mid-gray
↓ SDS C241104 safety-coat-green
↓ SDS C240903 Watco US Safety Coat Blue Kit
↓ SDS C240805 Watco US Safety Coat Tile Red Kit
↓ SDS C240502 Watco US Safety Coat Silver Gray Kit
AVAILABLE COLORS
5
RECOMMENDED NUMBER OF COATS
2
HOW TO APPLY
MIXING
Combine the base and activator components into a clean 2 gallon or 5-gallon plastic or metal pail. Use a paint paddle or spatula to scrape out and transfer as much of the material as possible. Mix the components thoroughly until an even, uniform color is achieved. If using a power mixer use a paint paddle or spatula to blend in any unmixed material from the sides and bottom of the pail. Do not mix more than one unit at a time. Immediately pour the material into a roller pan and do not delay the application. The pot life is approximately two hours at 60-70°F. Higher temperatures will reduce the pot life.
APPLICATION
Apply in a well-ventilated area when the air and surface temperatures are between 60-90°F. The air and surface temperature must be at least 60°F prior to application. Use a good quality lint-free 3/8" nap roller with a phenolic core. The first coat of Safety Coat will act as a priming/sealing coat on most surfaces. The second coat should be applied as soon as the first coat is dry (approximately 12 hours at 60-70°F). Do not exceed the maximum coverage of 240 sq ft per kit. Occasional stirring of the product will ensure a more even distribution of the aggregate. In exceptional temperature conditions, please contact a Watco Industrial Flooring Expert at (855) 627-6350.
SURFACE PREPARATION
The concrete surface must be clean, dry and free of loose material. New concrete should be allowed to cure for 28 days prior to coating. Remove oil, dirt, grease and other chemical contaminants by cleaning with detergent or another suitable cleaner. Rinse thoroughly. Use Cemtetch® Self Etching Cleaner to remove unsound laitance and create a proper surface profile to the concrete.
Rinse thoroughly and allow it to dry before the application of the Safety Coat. Previously coated floors need to be in good sound condition with proper adhesion to the concrete substrate. Glossy finishes should be sanded to provide a surface profile. Wooden surfaces should also be sanded. Two or three coats may be required on open textured surfaces such as chipboard. Not recommended for use onto metal or latex leveling compounds.
