Osmo UV-Protection Oil Tints Varnishes
UV-Protection Oil Tints VARNISHES
UV-PROTECTION OIL TINTS VARNISHES
Microporous, breathable finish which does not crack, peel, flake or blister
INFORMATION
BRAND
Osmo
PRODUCT TYPE
Varnishes
APPLICATIONS TOOL
- Osmo Flat Brush
- Osmo Microfibre Roller
FINISH
-Spruce (Satin) -Oak (Satin),
-Larch (Satin) -Douglas Fir (Satin) -Cedar (Satin) -Natural (Satin) -Light Red Cedar (Satin) -Light Oak (Satin)
COLLECTION
UV-Protection
RECOMMENDED USE
Vertical wood surfaces in outdoor areas
FINISHES
Colours (Satin)
COATS
1-2 coats
RECOAT
One coat, when signs of wear become visible
RECOMMENDED USE
Interior wooden flooring and furniture
SIZES
- 5m
- 125ml
- 750ml
- 2.5L
HIGH SOLID
Extremely durable and hardwearing
DRY TIME
12 hrs
CLEAN UP
Osmo Brush Cleaner
DOWNLOADS
↓ Safety Data
↓ Product Information
CARE
Osmo Wash and Care, or Spray-Mop
COAT
2 coats
COVERAGE
18m²/L with one coat
APPLICATIONS
No sanding necessary for future applications
DETAIL
- Very water and dirt resistant
- Reduces wood swelling and shrinkage
- Resists growth of algae, mildew and fungal
- No sanding necessary for future applications
- Looking for a clear finish? View UV-Protection Oil
- No sanding necessary for future applications
- NMicroporous, breathable finish which does not crack, peel, flake or blister
INSTRUCTIONS
SURFACE PREPARATION
-Wood surface must be clean, dry and frost-free (moisture content max. 18%). -Osmo Polyx®-Oil Original is ready to use. Do not thin. Stir well using a flat stirring stick or spatula before use.
-Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler). -Sand wood surfaces carefully. Begin with coarse sandpaper – final sanding work for flooring P120-150, for furniture P180-240. Before oiling the surface, remove sanding dust with a broom or vacuum. -The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
METHOD OF APPLICATION
With Osmo Flat Brush, Floor Brush, Oil Finish Applicator Fleece (Hand Pad Holder) or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 8-10 hours under good ventilation.
After drying, quickly apply a second coat also thinly. After 2-3 weeks, the surface is fully cured. When renovating or recoating an already oiled surface, one coat applied to the clean and dry surface is usually sufficient.
CARE
REGULAR CLEANING
Wood surfaces treated with Polyx®-Oil are highly repellent and easy to maintain. Remove debris with the Osmo green Dust-Mop from the Mop Cleaning Kit for Floors, or use a broom or a vacuum cleaner.Damp mop floors using diluted Osmo Wash and Care and the Osmo Micro-Mop Plush from the Mop Cleaning Kit for Floors. Avoid saturating the surface with water. For the convenient cleaning of floors use Osmo Spray-Mop. For furniture or small areas, use Osmo Spray Cleaner and Osmo Easy Pads.
RECOATING
Simply re-apply one coat onto the appropriately cleaned and dried surface when signs of wear become visible.
OCCASIONAL MAINTENANCE
For spot cleaning stubborn scuff marks, or occasionally refreshing satin or gloss Polyx-Oils use Osmo Liquid Wax Cleaner. Alternatively, Osmo Maintenance Oils can be used to occasionally refresh most Polyx Oil sheen levels, including matt. Ensure surfaces are appropriately cleaned before thinly applying Osmo Maintenance Oils.
COLORS
CLEAR FINISHES
