Osmo Polyx®-Oil Effect Raw Varnishes
POLYX®-OIL EFFECT RAW VARNISHES
POLYX®-OIL EFFECT RAW VARNISHES
Resistant to common liquid spillages such as water, juice, tea, cola and wine
INFORMATION
BRAND
Osmo
PRODUCT TYPE
Varnishes
RECOAT
One coat, when signs of wear become visible
COATS
2 coats (or 1, plus top coat of Polyx®-Oil Original)
FINISH (3044 RAW)
Almost invisible : The light character of the wood is retained. Untreated wood (left) and treated with Raw 3044 (right).
CLEAN UP
Osmo Brush Cleaner
COVERAGE
30m²/L with one coat
DRY TIME
24 hrs, remove white pigments from surface before leaving to dry
APPLICATION TOOLS
- Floor Brush
- Osmo Flat Brush
- Hand Pad or Osmo Microfibre Roller
RECOMMENDED USE
Lightly coloured wooden floors and furniture of domestic origin
FINISHES
Raw (Matt)
COLLECTION
Wood Wax
VISCOSITY
> 70s DIN EN ISO 2431/3 mm, thixotropic
PRODUCTION
Made in United Kingdom
ODOUR
Faint/mild, after drying odourless
DOWNLOADS
↓ Safety Data
↓ Product Information
WOOD SURFACES
- Pine
- Ash
- Larch
- Spruce
- Beech
- Oak ( avoid smoked or fumed Oak)
CAN SIZES
0.75 L; 2.50 L; 25 L
COLOUR TONES
3044 Raw Transparent
INGREDIENTS
Based on natural plant oils and waxes (sunflower oil, soya oil, thistle oil, carnauba wax and candelilla wax), paraffin, titanium dioxide white pigment, siccatives (drying agents) and water-repellent additives. Dearo- matized white spirit (benzene-free). EU limit value for this product (cat. A/i): 500 g/l VOC (2010). This pro- duct contains max. 500 g/l VOC.
SPECIFIC GRAVITY
0.94-0.96 g/cm³
FLASH POINT
> 60°C acc. DIN EN ISO 2719
STORAGE
Up to 5 years and longer if can is kept dry and closed tightly. If thickened by frost, store for 24-36 hours at room temperature before use.
CLEANING OF TOOLS
With Osmo Brush Cleaner (free of aromatic com- pounds).
POSSIBLE
Maple : apply very thinly and carry out a trial application before use.
ALMOST INVISIBLE PROTECTION
- Lightly white pigmented
- Very water and dirt resistant
- Extremely durable and hardwearing
- Light coloured wood stays light coloured
- Nearly invisible appearance, no ‘permanent wet effect’
- Saliva-resistant and sweatproof, suitable for children’s toys
- No sanding necessary for spot repairs or future applications
- Microporous, breathable finish which does not crack, peel or flake
INSTRUCTIONS
METHOD OF APPLICATION
-With Osmo Flat Brush, Floor Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Applying excess Polyx®-Oil Effect Raw 3044 may lead to a white chalky surface. Remove visible white pigments before allowing the surface to dry. Allow to dry for approx. 24 hours under good ventilation. -After drying, quickly apply a second coat also thinly. -When renovating or recoating an already oiled surface, one coat applied to the clean and dry surface is usually sufficient.
SURFACE PREPARATION
-Wood surface must be clean, dry and frost-free (moisture content max. 18%). -Osmo Polyx®-Oil Effect Raw is ready to use. Do not thin. Stir well using a flat stirring stick or spatula before use. -Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. -Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler).
-Sand wood surfaces carefully. Begin with coarse sandpaper – final sanding work for flooring P120-150, for furniture P180-240. Before oiling the surface, remove sanding dust with a soft brush or vacuum cleaner. Applying Polyx®-Oil Effect Raw over very textured or coarse surfaces could appear more white. -The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
CARE
-Regular cleaning : Dust mopping using the green dust-mop from the osmo mop cleaning kit for floors. Damp mopping using diluted osmo wash and care and the micro-mop plush from the osmo mop cleaning kit for floors. Alternatively use the convenient osmo spray-mop.
-Recoating : When slight signs of wear become visible, and providing the surface does not become completely bare, simply re-apply one thin coat onto the clean and dry surface. Avoid applying polyx®-oil effect raw to bare wood surfaces that have become dirty. Bare, dirty surfaces could appear more rich and dark following the application of the oil finish. A small trial is highly recommended first.
-Occasional maintenance : If the oiled surface remains light in colour yet there is a reduction in water repellency, refresh the surface with osmo maintenance oil 3079 clear matt. Before using osmo maintenance oil 3079, damp clean the surface using diluted osmo wash and care, or alternatively osmo spray cleaner and allow to fully dry. For small areas osmo maintenance oil 3079 can be applied thinly with a lint free cloth or white pad. Remove excess product. Allow for good ventilation while drying. A small trial is highly recommended first.
VIDEOS
DETAIL
- Osmo Polyx Oil Raw 3044 (Before you buy)
- Osmo Polyx Oil Raw 3044 (How to Apply)
- Osmo Polyx Oil Raw 3044 (How to Maintain)