Watco V2100 System Galvanizing Compound Spray by Rust-Oleum
V2100 SYSTEM GALVANIZING COMPOUND SPRAY BY RUST-OLEUM
V2100 SYSTEM GALVANIZING COMPOUND SPRAY BY RUST-OLEUM
V2117838
Easily Touch Up Galvanized Surfaces With Rust-Oleum High Performance V2100 System Galvanizing Compound Spray.
This 93% Pure Zinc Aerosol Coating Provides Maximum Corrosion Resistance And Excellent Adhesion On Galvanized Metal. The Excellent Durabilit Easily touch up galvanized surfaces with Rust-Oleum High Performance V2100 System Galvanizing Compound Spray.
This 93% pure zinc aerosol coating provides maximum corrosion resistance and excellent adhesion on galvanized metal. The excellent durability of this spray coating makes it ideal for moderate to severe industrial environments.
information
CURE TIME
Tack free in 20mins
BRAND
Watco
PRODUCT TYPE
Paint Spray
DETAIL
The excellent durability of this spray coating makes it ideal for moderate to severe industrial environments.
FINISH
Flat Metallic Finish
COVERAG
12-20 sq ft
COLOR
- Cold
- Bright
RECOAT TIME
Within 1 hour or after 24 hours depending on temperature
PRIMER SUGGESTIONS
Do not use primer
SKU
V2117838
USAGE INTERIOR/EXTERIOR
Interior or Exterior
SUITABLE FOR
Galvanized Steel
FEATURES AND BENEFITS OF V2100 GALVANIZING SYSTEM SPRAY PAINT
-Dries quickly in 20 minutes -Withstands heat up to 200°F -No primer required -Ideal for touch-up to galvanized ducts, storage tanks, fences, trailers, etc. -Performance offset to Federal Specifications DOD-P-21035A; MIL-P-26915C -Meets USDA requirements for incidental food contact; accepted for use in federally registered Canadian food facilities; VOC-compliant nationwide
HOW TO APPLY
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a solvent such as mineral spirits. Do not insert any object into can valve opening.
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with a commercial detergent, or other suitable cleaning method. Rinse with fresh water and allow to thoroughly dry. Remove loose paint and rust with a wire brush or sandpaper. Previously coated surfaces must be sound and in good condition. Smooth, hard, or glossy finishes should be scarified by sanding to create a surface profile.
SURFACE PREPARATION - WEATHERED GALVANIZED STEEL
Remove loose rust and stains by hand tool (SSPC-SP-2) or power tool (SSPC-SP-3) prior to application of the Cold Galvanizing Compound.
SURFACE PREPARATION - STEEL
Hand tool (SSPC-SP-2) or power tool (SSPC-SP-3) clean to remove loose rust, mill scale, and deteriorated previous coatings.
SURFACE PREPARATION - PREVIOUSLY COATED
Previously coated surfaces must be sound and in good condition. Smooth, hard, or glossy finishes should be scarified by sanding to create a surface profile.
DRY & RECOAT TIMES
Recoat within 1 hour or after 24 hours. Allow more time in cooler temperatures.
SURFACE PREPARATION - GALVANIZED STEEL:
New galvanized steel may contain a surface wax or oil from the fabricator. This must be removed with a cleaner & degreaser, commercial detergent or other suitable cleaner. NOTE: Only the V2100 System Galvanizing Compounds are to be used on galvanized steel. Do not use the other V2100 System Finish Colors.
CLEAN-UP
Wipe off tip before storing. Clean-up wet paint with xylene or mineral spirits. Properly discard empty container. Do not burn or place in trash compactor. Empty container can be recycled.
APPLICATION
Use when temperature is above 50°F (10°C) and humidity is below 85% to ensure proper drying. Surface temperature must be between 50-100°F (10-38°C). Protect surrounding surfaces from overspray. Overspray can carry a significant distance. Shake can for one minute after mixing ball is heard. Hold can 10-14 inches from surface. Apply several light coats a few minutes apart to avoid drips and runs.
