Kilz Kilz® Adhesion Interior | Exterior Primer
Kilz® Adhesion Interior | Exterior Primer
KILZ® ADHESION INTERIOR | EXTERIOR PRIMER
KILZ® ADHESION Primer is a water-base, modified-acrylic primer specifically formulated to bond to a variety of ‘tough-to-paint’ surfaces.
Its advanced chemistry provides a sound anchor for topcoats while reducing or potentially eliminating the need for sanding dense, glossy surfaces including Kynar®, PVC, vinyl, Formica®, glass, tile, glazed brick, chalky paints, glossy finishes, fiberglass and metals.
If using as a primer for epoxies, lacquers, products containing xylene or other hot solvents, allow to dry for 24 hours before topcoating and test for compatibility in an inconspicuous area before full coat application. For use on interior and exterior surfaces.
INFORMATION
BRAND
Kilz
PRODUCT TYPE
Paint
PRODUCTION
Made in USA
BASE
Water
APPLICATION TEMPERATURE
- Minimum : 50°F (10°C)
- Maximum : 90°F (32°C)
BRUSH
- Nylon
- Poly
COLOR
White
FINISH @ 85°
< 10
VISCOSITY
93 - 100 KU
MAX TINT
2 oz
DRY TO TOUCH
30 min
DRY TO RECOAT
1 hour
ROLLER
- Porous Surface : 3/8" - 1/2" nap
- Smooth Surface :1/2" - 3/4" nap
VOC
<50 g/L
SPRAY PRESSURE
2.500 - 3.200
WEIGHT SOLIDS
58% (+/-) 2%
VOLUME SOLIDS
33.64%
MATERIAL
If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations. For recycling or disposal information contact your local household refuse collection service.
DRY TIME @ 77°F (25°C), 50% RH
- Dries to the touch in 30 minutes.
- Can be recoated or topcoated in one hour with latex or oil-based paint.
- Lower temperatures, higher humidity, poor ventilation or heavy application can significantly increase dry and recoat times.
MILS (COVERAGE - LOW)
- Wet :5.3
- Dry : 2.2
MILS (COVERAGE - HIGH)
- Wet : 4
- Dry : 1.3
CLEAN-UP & DISPOSAL
-Clean equipment and paint spatters with warm, soapy water. -Do not dispose of this product down a drain. -Please consider donating any unused product. -For recycling or disposal information contact your local household refuse collection service. -If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current local, state and federal regulations.
COVERAGE
- Low : 300 sq. ft.
- High : 400 sq. ft.
SPRAY FILTER
60 mesh
SPRAY TIP
.017" - .021"
SURFACE PREPARATION
-All surfaces must be clean, free of dust, chalk, oil, grease, wax, polish, mold and mildew, loose peeling paint, rust and all other foreign substances. -If washing is necessary, use a non-soapy detergent or a TSP substitute, rinse well and allow to dry. -Unpainted, exterior wood exposed to sun and/or moisture longer than 2-4 weeks must be cleaned and sanded before priming. -†Glossy Surfaces: For maximum adhesion, scuff sand the surface thoroughly before priming.*-Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface.* -Mold or Mildew Covered Surfaces: Wash the area with a mildew remover, rinse with water and allow to dry before priming.
Masonry, Brick, Stucco and Plaster: KILZ 2 GRAY Primer may be used on clean, dry, aged masonry surfaces. New masonry must be allowed to cure (dry) at least 30 days before applying KILZ 2 GRAY Primer. Fire Restoration: It is critical to clean damaged surfaces thoroughly before priming. Primer recommendations: Water-based primers such as KILZ® RESTORATION or oil-based primers such as KILZ® ORIGINAL (interior use) or KILZ® ORIGINAL EXTERIOR.
APPLICATIONS
- Wear eye protection.
- Apply using a brush, roller or sprayer.
- Brush – High quality Nylon/Polyester
- Airless spray – .015-.021 tip / 60 mesh filter @ 2,500–3,200 PSI
- Stir thoroughly before and occasionally during use.
- Prime the entire surface to ensure a uniform appearance of the topcoat.
-Roller – High quality 3/8-1/2" nap on smooth surfaces or 1/2-3/4" nap on semi-rough or porous surfaces. -For spray applications, a small amount of water (no more than ½ pint per gallon) may be added. -Only apply if surface, air and product temperatures are between 50°-90°F (10°-32°C). -Finishing: Topcoat within 30 days to prevent contamination of the primer before painting. -Tinting: May be tinted with up to 2 oz. (60 mL) of universal colorant per gallon. Tinting to a lighter shade than the topcoat is recommended. -Coverage: 300-400 sq. ft.(28-37 m2) per gallon depending on application method and surface porosity.
