Kilz Kilz® Klear Interior & Exterior Primer
KILZ® KLEAR INTERIOR & EXTERIOR PRIMER
KILZ® KLEAR INTERIOR & EXTERIOR PRIMER
KILZ® KLEAR High Performance Sealer is a water-based fast dry multi-surface clear primer developed to seal porous surfaces inside and outside your home.
Particularly effective for “same color painting”, KILZ KLEAR Primer will bond and seal porous and chalky surfaces with little change to current color. KILZ KLEAR Primer is a tough, flexible and breathable film to offer years of service. KILZ KLEAR Primer may also be used to seal highly porous surfaces with a transparent flat finish.
Suitable for sealing torn drywall facing paper, dried wallcovering adhesive, ‘hot’ joint compounds, concrete and stucco. Use on interior and exterior surfaces including drywall, plaster, wood, galvanized, aluminum, architectural plastics, masonry and brick. Not recommended for floors.
INFORMATION
BRAND
Kilz
PRODUCT TYPE
Paint
INT/EXT
Int/Ext
BASE
Water
APPLICATION TEMPERATURE
- Minimum : 50°F (10°C)
- Maximum : 90°F (32°C)
BRUSH
- Nylon
- Poly
COLOR
Clear
FINISH @ 85°
< 10
ROLLER
- Porous Surface : 1/2" - 3/4" nap
- Smooth Surface : 3/8" - 1/2" nap
VOC
90 g/l
SPRAY PRESSURE
2.500 - 3.000
WEIGHT SOLIDS
19.7% (+/-) 2%
VOLUME SOLIDS
41.6% (+/-) 2%
DRY TIME @ 77°F (25°C), 50% RH
- To Touch: 30 Minutes
- Recoat or topcoat after 1 hour.
- Dries to the touch in 30 minutes at 77°F (25°C) and 50% humidity.
COVERAGE
- Low : 300 sq. ft.
- High : 400 sq. ft.
SPRAY FILTER
60 mesh
SPRAY TIP
.017" - .021"
MILS (COVERAGE - LOW)300 sq. ft.
- Wet : 4
- Dry : 0.7
MILS (COVERAGE - HIGH)400 SQ. FT.
- Wet : 5.3
- Dry : 0.9
CLEAN-UP & DISPOSAL
-Clean equipment and paint spatters with warm, soapy water. -Do not dispose of this product down a drain. Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service. -If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations. For recycling or disposal information contact your local household refuse collection service.
APPLICATIONS
-Use product when the surface and air temperatures are between 50-90°F (10-32°C). -Stir thoroughly before and occasionally during use. -Do not thin or apply at a greater spread rate or build up a visual glaze on the surface. Product is formulated for use at package consistency only. -Brush – High quality Nylon/Polyester -Roller – High quality 3/8-1/2" nap on smooth surfaces or 1/2-3/4" nap on semi-rough or porous surfaces. -Airless spray–.017-.021 tip / 60 mesh filter -Coverage: 300-400 sq. ft. (18.6-27.9 m2) per gallon, depending on the surface texture, porosity and the application method.
SURFACE PREPARATION
The following steps are recommended for product performance.
-All surfaces must be clean, free of dust, chalk, oil, grease, wax, polish, mold and mildew, loose peeling paint, rust and all other foreign substances. -If washing is necessary, use a non-soapy detergent or a TSP substitute, rinse well and allow to dry. -Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead is hazardous*. -Glossy Surfaces: Use only over properly prepared glossy surfaces, scuff-sand to de-gloss and wipe clean before application. -Mold or Mildew Covered Surfaces: Wash the area with a mildew remover, rinse with water and allow to dry before priming.
