Ronacrete RonaDeck Resin Bonded Surfacing Composites
RonaDeck Resin Bonded Surfacing Composites
RONADECK RESIN BONDED SURFACING COMPOSITES
Rapid cure decorative slip resistant safety surfacing
RonaDeck Resin Bonded Surfacing is a resin bonded aggregate surfacing system for paths, car parks, drives, ramps, highways etc.
INFORMATION
COVERAGE RATES (0.9—1.4MM AGGREGATE)
- Ronadeck Resin Bonded Aggregate : 7kg Per M²
- Ronadeck Resin Bonded Gp Primer : 6-8m² Per Litre
- Ronadeck Resin Bonded Steel Primer 9-10m² Per Litre
- Ronadeck Resin Bonded Surfacing Resin : 1.0kg Per M²
- Ronadeck Resin Bonded Seal Coat (1st Coat): 3.8m² Per Litre
- Ronadeck Resin Bonded Seal Coat (2nd Coat) : 4m² Per Litre
BRAND
Ronacrete
PRODUCT TYPE
Composites
FEATURES AND BENEFITS
-Rapid cure resin.-DDA compliant.-Highly decorative.-Thin surface dressing.-Available in a wide range of finishes.-Self priming on asphalt and concrete.-Suitable for pedestrian and vehicular traffic.-High slip resistance - tested to BS 8204-6:2008+A1:2010 Appendix B.
USES
-Steps, car parks and ramps.-Balconies, common walkways. -Landscaping, gardens, driveways, footpaths. -Slip resistant surfacing on platforms, footbridges. -Marinas, jetties, sea walls, pond and lake surrounds. -Approaches to pedestrian crossings, junctions and other hazards.
CONTRACTORS
-RonaDeck Resin Bonded Surfacing is a specialist product and must only be applied by specialist applicators. -Do not apply or allow RonaDeck Resin Bonded Surfacing to be applied by contractors who do not possess the necessary skills and experience
COVERAGE RATES (1—3MM AGGREGATE)
- RonaDeck Resin Bonded GP Primer : 6-8m² per litre
- RonaDeck Resin Bonded Steel Primer : 9-10m² per litre
- RonaDeck Resin Bonded Surfacing Resin : 1.5kg per m²
r litre
- RonaDeck Resin Bonded Aggregate 8kg per m²
- RonaDeck Resin Bonded Seal Coat (1st coat) : 3m² per litre
- RonaDeck Resin Bonded Seal Coat (2nd coat) : 5m² pe
COLLECTION
RonaDeck
PRODUCTION
Made in United Kingdom
LANDSCAPING
RonaDeck Resin Bonded Surfacing is an alternative to loose stone and gravelpaths, driveways, pond and lake surrounds. Loose gravel can be untidy, creating mess, unnecessary dust and introducing a slip or trip hazard. RonaDeck Resin Bonded Surfacing bonds natural aggregate securely to suitable surfaces creating a gravel or stone appearance but without the associated mess and inconvenience
COVERAGE RATES
Note that coverage rates quoted are theoretical and based on application onto smooth non-porous surfaces; actual coverage rates can be assessed only by practical trials on representative areas of the structure and these are recommended in all situations, especially where surfaces are rough texture and /or porous.
PACKAGING
- Ronadeck Resin Bonded Gp Primer : 5 Litres
- Ronadeck Resin Bonded Steel Primer : 5 Litres
- Ronadeck Resin Bonded Surfacing Resin : 18kg
- Ronadeck Resin Bonded Surfacing Aggregate : 25kg
- Ronadeck Resin Bonded Seal Coat Uv : 5 Litres And 22 Litres
TEMPERATURE AND HUMIDITY
-RonaDeck Resin Bonded Surfacing is a rapid setting and rapid curing product and working time will be restricted at high temperature. -Do not apply RonaDeck Resin Bonded Surfacing when air or substrate temperature exceeds 250C. -At low temperatures the resin will not flow sufficiently to achieve a smooth finish and work should not proceed when the temperature is less than 50C. -Do not apply RonaDeck Resin Bonded Surfacing when relative humidity is greater than 60%. -Do not apply RonaDeck Resin Bonded Surfacing when surface temperature is less than 20C above the dew point.
APPEARANCE AND EXPECTATIONS
Because of the random size, grading and colour of the aggregate and the way it is cast, it is inevitable that the appearance and density of aggregate will vary across the surface. It is likely that in some areas there will be patches where more resin is visible. Careful installation will reduce the variability but a uniform surface with no visible resin should not be expected
Some unbonded or partially bonded aggregate will be temporarily locked into other aggregate. Shortly after installation and perhaps for several weeks or months, aggregate will be shed from the surface and must be removed to prevent further aggregate loss. Loose stones are therefore to be expected and may be carried into buildings and vehicles on the soles of shoes. A combination of mechanical sweeping and vacuum removal is the best method for early removalof aggregate.
SUBSTRATE SUITABILITY
-Only apply to a suitable substrate. The best substrate is a well designed and constructed concrete, shot blasted to remove laitance. -RonaDeck Resin Bonded Surfacing must be installed on to a dry surface. -RonaDeck Resin Bonded Surfacing can also be applied to suitably designed and constructed asphalt or asphalt concrete (macadam). The bitumen binder should be maximum 90 pen, 40/60 pen is preferred. The contractor should be satisfied that the substrate is adequately compacted. Older asphalt or asphalt concrete may be too weak for application of resin bonded surfacing.
-New asphalt or asphalt concrete should be at least 2-3 weeks old before application of RonaDeck Resin Bonded Surfacing. -RonaDeck Resin Bonded Surfacing can be applied to dimensionally stable timber and metal surfaces which are clean, unpainted, untreated with oils or paints or other adhesion-limiting treatments. -Only apply RonaDeck Resin Bonded Surfacing to substrates which have adequate tensile strength. -Application to any other surface is likely to result in early failure.
-If you are unsure of the suitability of a substrate for application of RonaDeck Resin Bonded Surfacing, do not proceed. -RonaDeck Resin Bonded Surfacing is a thin layer of 1mm to 4mm (approximately) depending on the system. It will therefore reflect any substrate imperfections. Uneven substrates should therefore be levelled before application of RonaDeck Resin Bonded Surfacing to avoid uneven wear and unacceptable appearance.
INSTRUCTIONS FOR USE
HEALTH AND SAFETY
Refer to Safety Data Sheet
CLEANING
A Xylene based solvent should be used for cleaning tools etc
SITE ATTENDANCE
When on site Ronacrete representatives are able, if asked, to give a general indication of the correct method of installing a Ronacrete product. It is important to bear in mind that Ronacrete Ltd is a manufacturer and not an application contractor and it is therefore the responsibility of the contractor and his employer to ensure he is aware of and implements the correct practices and procedures to ensure the correct installation of the product and that liability for its correct installation lies with the contractor and not with Ronacrete Ltd.
PROPERTIES
RonaDeck Resin Bonded Surfacing has excellent fuel and chemical resistance. Applied correctly the tensile bond strength of RonaDeck Resin Bonded Surfacing is greater than the cohesive strength of the concrete, or other suitable substrate
INSTRUCTIONS FOR USE
Optionally, apply RonaDeck Resin Bonded Seal Coat / RonaDeck Resin Bonded Seal Coat UV to improve aggregate retention and aid cleaning. One or two coats should be applied. Do not apply RonaDeck Resin Bonded Surfacing or RonaDeck Resin Bonded Seal Coat if rain, fog, or high humidity is expected within its cure time or if the resin or aggregate has become dampApply by roller at the rate of 3m2 per litre for the first coat and 5m2 per litre for the second coat on 1-3mm aggregate, or 3.8m2 per litre for the first coat and 4m2 per litre for the second coat on 0.9-1.4mm aggregate. Refer to separate data sheet for further information.
AGGREGATE SELECTION
RonaDeck Resin Bonded Surfacing Aggregates have been chosen for their suitability for individual applications. Some aggregates such as Sepia are suitable for light traffic while others such as bauxite provide high polished stone values, wear resistance and skid resistance. Some aggregates are inherently weak and will therefore have been excluded from our selection. 1-3mm bauxite is the ideal aggregate for vehicle traffic. 0.9-1.4mm bauxite is suitable for pedestrian use.
AGGREGATE COLOUR AND SHADING
The sourcing and processing of the natural and pigmented aggregates supplied with RonaDeck Resin Bonded Surfacing cannot eliminate variability in their colour, shading and grading even though strict quality control measures are in place. We are therefore unable to guarantee that aggregates will be free from such variation and cannot accept any liability for any variation. Note that coloured aggregates are colour coated and will fade under UV light.
SHELF LIFE AND STORAGE
Store unopened in dry warehouse conditions away from frost and direct heat or sunlight in the temperature range 5°C – 25°C. Shelf life of unopened containers— RonaDeck Resin Bonded Surfacing resin 12 months, RonaDeck Resin Bonded Pore Filler 9 months, RonaDeck Resin Bonded Seal Coat 6 months, RonaDeck Resin Bonded GP Primer 12 months and RonaDeck Resin Bonded Steel Primer 24 months.
AGGREGATE SELECTION
RonaDeck Resin Bonded Surfacing Aggregates have been chosen for their suitability for individual applications. Some aggregates such as Sepia are suitable for light traffic while others such as bauxite provide high polished stone values, wear resistance and skid resistance. Some aggregates are inherently weak and will therefore have been excluded from our selection. 1-3mm bauxite is the ideal aggregate for vehicle traffic. 0.9-1.4mm bauxite is suitable for pedestrian use
