Ronacrete RonaDeck Resin Bonded Seal Coat UV
RONADECK RESIN BONDED SEAL COAT UV
RONADECK RESIN BONDED SEAL COAT UV
INFORMATION
FEATURES AND BENEFITS
- UV stable
- Ready to use
- 1 or 2 coat application
- Clear polyurethane coating
- Increased abrasion and frost resistance
- Improved chemical resistance and ease of cleaning
- Sealer for RonaDeck Resin Bonded Surfacing • improved aggregate retention
PRODUCT TYPE
Mortars
HEALTH AND SAFETY
Refer to Safety Data Sheet
COVERAGE
- Touch Dry : 2—5 hours @ 20°C - Re-coatable : 2—24 hours @ 20°C 90%
- Cure : 24 hours @ 20°C - Flash Point : 28°C
- Application Temperature : 5°C to 25°C
COLLECTION
RonaDeck
PRODUCTION
Made In United Kingdom
DOWNLOADS
↓ Data Sheet
↓ Safety Datasheet
LIMITATIONS OF USE
- Apply to dry surfaces only
- Flammable - do not use near naked flame
- Protect from rain and adverse weather until fully cured
SPILLAGE
Wash small spills away with water; soak large spills with earth or sand. Avoid contact; inform authorities if major spillage occurs.
PACKAGING
RonaDeck Resin Bonded Seal Coat UV is supplied in 5 litre and 22 litre units
SHELF LIFE AND STORAGE
Shelf life is 6 months. Replace lid immediately after use. Once opened use the material within 2 days. Store in a dry place out of direct sunlight at 5-30°C.
LOW TEMPERATURE APPLICATION
To reduce the cure time of Seal Coat in cold conditions add 1% RonaDeck Resin Bonded Seal Coat Accelerator. This will reduce the cure time and overcoat/traffic time by 50%.
DESCRIPTION
RonaDeck Resin Bonded Seal Coat UV is a clear polyurethane sealer suitable for internal and external use. Use to seal, bind and protect RonaDeck Resin Bonded Surfacing surfaces. Used as a two coat seal the following benefits can be achieved:
- Improved aggregate retention and weathering resistance
- Increased abrasion resistance
- Surface is easier to clean
- Chemical resistant against a wide range of chemicals and solvents
– Check with the Ronacrete Technical Department
COVERAGE
- 1—3mm Aggregate : 1st coat 3m² per litre 2nd coat 5m² per litre
- 0.9—1.4mm Aggregate : 1st coat 3.8m² per litre 2nd coat 4m² per litre
SITE ATTENDANC
When on site Ronacrete representatives are able, if asked, to give a general indication of the correct method of installing a Ronacrete product. It is important to bear in mind that Ronacrete Ltd is a manufacturer and not an application contractor and it is therefore the responsibility of the contractor and his employer to ensure he is aware of and implements the correct practices and procedures to ensure the correct installation of the product and that liability for its correct installation lies with the contractor and not with Ronacrete Ltd.
INSTRUCTIONS FOR USE
Thoroughly clean all surfaces to remove loose material, dirt, dust, grime etc. Remove any standing water to leave the surface as dry as possible. Any moss, algae or fungal growth should be treated with RonaBond Fungicidal Treatment followed by hosing, stiff brushing and drying.
1. Apply the first coat of RonaDeck Resin Bonded Seal Coat UV using a short nap roller at the appropriate rate. Coverage rate is determined by the size of the applied aggregate and is best determined by practical trial.
2. If applying a single coat only allow to cure for 2-5 hours then traffic. If applying a second coat allow the first coat to cure for at least 1 hour but not more than 24 hours.
3. Apply the second coat in the same manner as described in 1. above.
4. Allow to cure for 2-5 hours then traffic
5. Avoid over treating as this will create a surface glaze
Note : The application of RonaDeck Resin Bonded Seal Coat will change the appearance of the aggregates and highlight inconsistent application of RonaDeck Resin Bonded Surfacing. Uneven application will create directional shading.
