Volteco Revomat Fibreglass Mesh
REVOMAT FIBREGLASS MESH
REVOMAT FIBREGLASS MESH
An AR fibreglass mesh which, thanks to high resistance to the alkalis contained in the cement, is not affected by oxidation and disaggregation.
information
PRODUCT APPLICATION
In combination with mortars and/or plasters to provide widespread partition of stresses
PACKAGING AND STORAGE
Revomat is available in rolls of 30 m², with width of 100 cm and length of 30 m.
BRAND
Volteco
PRODUCT TYPE
Fibreglass Mesh
COMPOSITION
- Anti-alkaline finish : 18% approx.
- AR fibreglass (according to UNI EN 15422) : 82% approx.
TENSILE STRENGTH OF THE FINISHED MESH (ISO 4606)
-Warp : Approximate tensile strength value 75 kn/m elongation 2.4% ±1
-Woof : Approximate tensile strength value 75 kn/m elongation 2.6% ±1
DOWNLOADS
↓ Ts_revomat_191_en.pdf
↓ Cp_revomat_en.docx
↓ Cp_revomat_en.pdf
↓ Ds_tanking With Bi Mortar Plaster Seal, Plastivo And Amphibia_518_en.pdf
COLLECTION
Bi
PRODUCTION
Made in Italy
HANDLE
Easy to cut
MESH DIMENSION
335 g/m² ±10%
THICKNESS
Reduced footprint thanks to low thickness warp and weft crossings
DETAIL
The quoted data are obtained in a laboratory at +20°C and 60% RH.
NOTES
Fill all of the gaps between mesh and wall thoroughly with mortar to ensure maximum compactness and adhesion.
MATERIAL
- Steel
- Cement
SAFTEY
It is recommended to use gloves while working
ADVANTAGE
-Good flexibility to facilitate shaping for changes in direction -High tensile strength (approximately 3 times greater than steel) -Excellent durability, unalterable in damp and chemically aggressive environments -It features a special anti-alkaline surface treatment (finish) which enhances the properties and provides dimensional stability -Light and easy to handle, easy to cut
![Volteco Revomat Fibreglass Mesh](http://{"type":"application/jidipi-edit","data":"<figure class=\\"jdp-reset jdp-image-figure\\" data-ce-tag=\\"image-figure\\"><div class=\\"jdp-mask\\" data-ce-tag=\\"mask\\"><a href=\\"https://upload.jidipi.com/posts/d00098229/3-tjl.jpg\\" class=\\"jdp-reset jdp-link\\" target=\\"_blank\\"><img src=\\"https://upload.jidipi.com/posts/d00098229/3-tjl.jpg\\" data-image-id=\\"662a42b2ee3629404bb309d1\\" srcSet=\\"https://upload.jidipi.com/fit-in/420x0/posts/d00098229/3-tjl.jpg 420w, https://upload.jidipi.com/fit-in/700x0/posts/d00098229/3-tjl.jpg 700w, https://upload.jidipi.com/fit-in/900x0/posts/d00098229/3-tjl.jpg 900w\\" data-image-name=\\"3.jpg\\" width=\\"341\\" height=\\"300\\" loading=\\"lazy\\" class=\\"jdp-image jdp-reset\\"/></a></div></figure>"})
PREPARATION AND APPLICATION
-Preparing the surfaces : Preventively position the CONNECTOR 20 by means of BI FIX chemical fixing (see relevant technical data sheets).
-Application : Apply a first layer of mortar between 1 and 2 cm, in any case equal to half the total thickness to be achieved, embed in revomat which must be fixed to the connectors 20. Overlap the edges of the adjacent sheets by at least 10 cm; then apply a second layer of mortar to fully cover the mesh.
