Artesive Wood Series – WD-004 Light Oak Opaque
ARTESIVE WOOD SERIES – WD-004 LIGHT OAK OPAQUE
ARTESIVE WOOD SERIES – WD-004 LIGHT OAK OPAQUE
Wood Grain Vinyl Films
FEATURES
DESIGN
Realistically texture similar to real wood. Thanks to the increased thickness of the grain feel a lot more touch than films of other brands.
CONFORMABLE
With the change in temperature the film stretches and allows the installer to make it stick even in difficult spots such as corners or edges.
BUBBLE FREE SYSTEM
Thanks to the special composition and to the thickness of the upper, it is possible to drastically reduce the irritating air bubbles during the application.
UNIMMEDIATE FIXING
The adhesive of Artesive vinyl films does not have the bite immediately to allow the immediate detachment and repositioning on the surface.
INFORMATION
BRAND
Artesive
SKU
ART-WD-004
CATEGORY
Wood Grain Vinyl Films
MATERIAL
Polyvinyl Chloride (PVC)
CHOOSE YOUR ROLL
Choose the width you need to minimize waste and facilitate application. You can choose between the various pre-cut rolls or the customized roll by indicating in the quantity field the exact meters required. This model is available in 4 different widths. 30 cm, 60 cm, 90 cm and 122 cm.
REPOSITIONNABLE
No
ADHESIVE
Permanent acrylic.
DETAIL
“Per linear meter” means that according to the quantity inserted in the cart, the footage corresponds and will always be on a single continuous roll.
HEAT RESISTANCE
180 °C
APPLICATION METHOD
Dry
PERFORMANCE STONE SERIES
- Bonded Sea
- Touch Feeling
- Conformability
- Ease of Application
- Internal Use & External Use
- Suitable for Car Wrapping
- Resistance to Cleaning agents
CERTIFICATION
UNI EN 12149:1999
WARRANTY
3 years internal use only
LIGHT OAK OPAQUE
The Light Oak model has a shade of light brown as the base colour, with grain in relief verging on beige. The opaque finish has graining in a vertical direction relative to the length of the coil.
MINIMUM CLASS OF REATION TO FIRE
NPD does not fireproof material
THICKNESS
220 μ ± 10%
NARROWING MARGIN
2% ca
OPTIMAL APPLICATION TEMPERATURE
15/30°C
QUALITY AND EASY APPLICATION
-Like all Artesive self-adhesive films, including this Stone series are conformable, in which heating them allows you to model and apply them easily in tricky areas such as edges or corners. The adhesive being used is not set immediately to 100%, but allows you to remove the film to be repositioned in the event of errors. The patterns and textures of the Artesive Stone series is in line with the trends of furniture of the moment. -See the diagram below for some of the performance normally required by an adhesive coating for interiors. On a scale of 0 to 100 where 100 is the highest score, you can figure out which model is suitable for your use.
PRODUCT TERM APPLIED INSIDE
Min 5 years
LINER MATERIAL
Kraft thickness120 μm ±10%
ROLL LENGTH
- 2.5 mt
- 5 mt
- 10 mt
ROLL WIDTH
- 30 cm
- 60 cm
- 90 cm
- 122 cm
WOOD SERIES
The Artesive wood series is the perfect combination of materials, design and performance of application. This self-adhesive film made of PVC offers very special features, perfect to be used to coat surfaces such as wood, plastic, metal and smooth surfaces such as plasterboard or MDF.
It’s surface has high thickness allowing a good feeling to the touch as well as sight. The grain feel and look very similar to natural wood.
PRODUCT TERM APPLIED TO THE OUTSIDE
ND
DOWNLOADS
↓ Data Sheet
↓ Warranty
SMALL TIPS
-If you need to make large surfaces, we suggest you to buy a small test roll, or a single roll, to verify that your imagination and color are exactly the ones you were looking for. -It is always better to apply the film lightly initially, to be sure of the correct positioning. -If you need larger films with larger sizes, you can contact us for a specific quote.
APPLY THE SELF-ADHESIVE FILM
APPLICATION
The application of the film is usually done step by step. After taking the measurements, the necessary part is cut, leaving always a margin of tolerance. On the back of the film, a grid helps you make a precise and in-line cut.
SURFACE
The film is repositionable at first, so do not be afraid to make mistakes. To help you first wet the surface to be treated with water, it will help you not to immediately attack the film.
CUT TO SIZE
Once cut to size, the film is still placed with the protective sheet applied on the surface, stopping it with paper tape. Starting from one side only a small part of the adhesive protection is removed and glued to the surface.
REMOVED
Any air bubbles can be removed with the help of a spatula. When the first piece of film is applied, the paper protection sheet is removed step by step.
OUTSIDE REMOVING AIR
Do not remove everything, but one piece at a time, continuing to pass the spatula every time from the center to the outside removing air bubbles and any drops of water previously applied. When the application is complete remove the pieces of paper tape. Voilà, done!