Diasen Acriflex X Pro Waterproofing
Acriflex X pro Waterproofing
ACRIFLEX X PRO WATERPROOFING
Maximum flexibility for extreme temperatures
This product is characterized by a special formula that allows the product to have high resistance and elastic modulus (high resistance to crack bridging).
Being that the product is fibre-reinforced, it does not require a reinforcement mesh. Moreover, it is flexible at very low temperatures (down to -25 ° C).
INFORMATION
CLEANING
The equipment used can be washed with water before hardening of the product.
SAFETY
During handling, always use personal protective equipment and follow the product safety data sheet.
BRAND
Diasen
ELASTOMERIC
Resins
MIXING
Acriflex X-Pro is ready to use. Before application it is recommended to mix it well in order to make the product homogeneous. In extremely hotweather conditions, it is possible to add 5% clean water and continue mixing. Never add extraneous components to the product
WOOD
Thoroughly clean the surface eliminating dust of rain over not completely dry product, carefully verify the suitability of the next covering
PREPARATION OF SUPPORT
The substrate must be completely hardened andresistant enough.The surface must be thoroughly clean, dry, without oils, greases, debris or detaching partsor other materials that may compromise the product adhesion. If the support is crumbly in its entirety, totally scrape it until obtaining a good support and restore lesions or damaged parts with suitable mortar. Potential humidity and the vapour caused by radiation can compromise the adhesion of the applied products. In case of hydro-cleaning, wait for the complete drying of the support. Before applying the product, it is recommended to protect all those elements that should not be covered by the product. If the product is applied on balconies and terraces, the support must have the inclination necessary for the water to drain
SMOOTH OR TILED SURFACES
Ensure that the tiles are well attached to the support otherwise remove them and restore them with suitable cement mortar. The tiled surface must not contain traces of release substances such as fats, waxes, oils, chemicals, etc. After having thoroughly cleaned the support,the surface must be treated with Grip Primer (see technical data sheet). To fill the joints between the tiles and create a perfectly level surface, apply the product WATstop (see technical data sheet). WATstop should also be used if the support is damp or affected by rising dump. Given the wide variety of tiles on the market, it is recommended to perform a test to verify the perfect adhesion of the system.
PACKAGING
-5 kg or 20 kg plastic bucket. Pallet -5 kg bucket - 20 boxes - 4 buckets each - (400 kg) . -20 kg plastic bucket - 48 buckets (960 kg
BENEFITS
-Special formula able to lend to the product high resistance to water stagnation and high elastic modulus -Fibre reinforced, thus not in need of a reinforcement armour. -Walkable, it can be left exposed -Tiles can be attached directly to Acriflex X- Pro, in accordance with EN 14891. -Flexible at low temperatures -Crack bridging resistance -Waterproofing achieved with low thicknesses. -It creates a continuous layer without joints, while adapting to complex support geometries. -Ready to use, easy and quick to apply -Resistant to UV rays, weathering agents,and marine and industrial environments
CONCRETE
In the case of newly built cementous substrate, it must be sufficiently cured. If injuries, holes or irregular areas are present on the substrate, restore them with suitable cement mortar. For a better adhesion on smooth, non-wet concrete it is recommended the use of Grip Primer (see technical data sheet). On moist supports, in order to avoid blistering or detachment phenomena, use Vapostop (see technical data sheet) as a primer. If the support is subject to rising damp, it is necessary to use WATstop (see technical data sheet). WATstop can also be used to fill small cracks or loopholes. On rough concrete use Vapostop (see technical data sheet)
METAL
Thoroughly clean the surface eliminating dirt and any paints not well adhesive. Before applying Acriflex X-Pro, prime the metal surfaces with Grip Primer (see technical datasheet). If the metal surface is painted, it is recommended to verify the perfect adhesion of the system. For supports not present in the technical sheet contact the technical officeDiasen.
certifications
SUSTAINABILITY CERTIFICATIONS
Recognizes that Decork Alfareflex has the ability to contribute to healthier spaces, healthy air, better thermal comfort and energy saving.
PERFORMANCE CERTIFICATIONS
The CE marking identifies Ultragum as a product complying with European construction standards and the rules governing its distribution and use.
PERFORMANCE CERTIFICATIONS
Decork Alfareflex is recognized compliance and attention to atmospheric pollution. This product does not emit volatile organic compounds.
