San Marco Marcotech Ultra Au40 Paint

When the work is finished, use water to clean the tools.Use product according to current health and safety regulations especially if applied indoors (face-mask, airing). On tannin-rich woods, to avoid dark stains forming, apply the insulating primer unimarc primer antitannino.

RESISTANT 

- High surface hardness
- Abrasion and scratch resistance

MATERIAL 

- Galvanized Surfaces
- Hard Pvc
- Metal Or Aluminium

USABILITY 

Easy to use and ready to use; clean tools with water

STORAGE 

- Maximum temperature for storage stability : +30 °C
- Minimum temperature for storage stability : +5 °C
- The product should be preferably used within 2 years from date of manufacture when stored in original unopened containers and in appropriate temperature conditions.

FEATURES 

-Attrezzi -Diluente : Water
-Diluizione con spruzzo
-Resa : 6-7 m²/l at 2 coats
-Diluizione con rullo : Ready to use
-Indoor Air Quality : A
-Strati : At least 2
-Diluizione con pennello : Ready to use
-Marcromie : Tinting System Marcromie

INSTRUCTIONS FOR USE 

- Suitably pre-treated ferrous metal substrates
- Wood substrates that are dimensionally stable, new or already varnished
- Galvanized surfaces, aluminum and light alloys, pvc, after application of a primer
- Be careful when treating wood rich in tannin. To reduce dark stains forming, apply insulating primer unimarc primer antitannino cod. 3080001/0019.

APPLICATION INSTRUCTIONS 

- Brush/roller ready to use, or max. 5%
- Airless max. 5% (nozzle diameter 0.011-0.015 mm, pressure approximately 200 bar)
- Low pressure max. 20% (nozzle diameter 1.8-2.2 mm, pressure air approximately 0.5 bar)
- High pressure max 20% (nozzle diameter 2-2.5 mm, air pressure approx. 2-3 bar)
- Tools cleaning must be done with water immediately after use.
- Indicative spreading rate : 6-7 sq.m/l based on 2 coats, creating a dry thickness of 60 micrometers.

TECHNICAL SPECIFICATIONS 

-Solvent : Water
-Gloss per uni en iso 2813: 40 at 60°
-Indoor air quality classification : A
-Type of binder : Acrylic-urethane copolymer in water dispersion
-Specific gravity per uni en iso 2811-1: 1.10-1.35 kg/l according to the colors.
-Viscosity per uni 8902 : 2000±300 cps. At 25 °c (brookfield rotational viscometer).
-Drying (25 °c and 65% r.H.) : Dust free 30 min; to touch 1 hour; to recoat after 5 hours

SURFACES IN PLASTIC MATERIAL (PVC) 

- Apply 2 layers of marcotech ultra.
- Sand the surface area to roughen it slightly.
- Degrease with suitable thinner and clean the substrate.
- On a clean and dry substrate, apply 2 layers of unimarc fondo universale series 335 or 1-2 layers of primer 1630307.

GALVANIZED SURFACES, ALUMINUM AND LIGHT ALLOYS 

- Apply 2 layers of marcotech ultra.
- Remove any traces of oxides by mechanical or manual cleaning.
- Carefully degrease with suitable alkaline solutions or thinner.
- Remove any layers of old, poorly-adhering paints, and sand the entire surface in to roughen it.
- Remove all traces of dust and, on a perfectly dry substrate, apply 1-2 coats of primer 1630307 rust inhibitor.

FERROUS METAL SURFACES 

- Apply 2 layers of marcotech ultra.
- Remove all traces of dust and dirt.
- Degrease the substrate with a suitable thinner.
- Apply 1-2 coats of primer 1630307 anti-rust onto a perfectly dry substrate.
- Remove any layers of old paints that do not adhere well, and sand the entire surface.
- Remove, by mechanical or manual cleaning, any flakes from laminations that do not adhere perfectly, and any traces of rust.

WOODEN SURFACES 

- Apply 2 layers of marcotech ultra.
- Remove any resins using a suitable thinner.
- Sand to remove lifted-up wood fibers and sharp edges.
- Fill the imperfections with a synthetic filler. Sand the filler and remove the dust.
- Remove any layers of old peeling-off paints and roughen up all the already-painted surfaces.
- Apply primer unimarc fondo universale series 335, or marconol orientalite series 145, or rapid series 144 onto a dry and clean substrate.