Keim Aquaroyal-Color Exterior Paint
KEIM AQUAROYAL-COLOR EXTERIOR PAINT
KEIM AQUAROYAL-COLOR EXTERIOR PAINT
Hydroactive technology meets creative design. Building physics instead of biocides.
Silica sol silicate paint according to DIN EN 1062-1 with hydrophilic surface and hydroactive properties, without addition of biocides for optimised, toxin-free algae prevention, two coats on KEIM Aqua-ROYAL mineral render, system component of KEIM AquaROYAL insulation systems.
KEIM AquaROYAL-Color is awarded with Cradle to Cradle Certified® Silver and C2C Certified Material Health Certificate™ Gold.
INFORMATION
PH VALUE
Approx. 11
ORGANIC CONTENT
< 5 %
DENSITY
Approx. 1.5 - 1.7 g/cm³
COLOUR FASTNESS (FB-CODE PURSUANT TO BFS LEAFLET NO. 26)
A1
COLOR SHADE
White and colour shades.
DOWNLOADS
↓ Safety Instructions Sheet
↓ Technical Data Sheet
↓ Environmental Product Declaration Information Sheet
↓ Brochure Sheet
↓ Brochure AquaRoyal Information
↓ STDS Aquaroyal Information Color Sheet
↓ Keim Silicate Paints Information Sheet
GENERAL INFORMATION
Cover surfaces not to be treated, especially glass, ceramics and natural stone. Any splashes on surrounding surfaces or traffic areas must be rinsed off immediately with plenty of water. Mixing with products not part of the system or other foreign additives is not permitted.
CONSUMPTION
Approx. 0.5-1.0 kg/m² for two coatings.
APPLICATION
-Block Brush
-Roller
-Airless Sprayer
PACKAGING
| TYPE OF CONTAINER | CONTAINER CONTENT | UNIT OF MEASURE | QUANTITY ON PALLET |
|---|---|---|---|
| Bucket | 25 | kg | 24 |
| Bucket | 5 | kg | 70 |
| Bucket | 2.5 | kg | 80 |
FIELD OF APPLICATION
KEIM AquaROYAL-Color is a system component of the hydroactive AquaROYAL systems and is used as a two-coat facade paint on KEIM AquaROYAL mineral plaster.
CLASSIFICATION
- Classification according to: DIN EN 1062-1
- Classification according to VOB: Silicate emulsion paint according to DIN 18363 sec. 2.4.1
- Water vapour diffusion current density (V-value): ≥ 2000 g/(m² · d)
- Diffusion-equivalent air layer thickness (sd-value): ≤ 0,01 m
- Diffusion-equivalent air layer thickness class: V1
- Test standard Diffusion equivalent air layer thickness: DIN EN ISO 7783
- Water permeability: > 1,0 kg/(m²√h)
- Water permeability rate class: W1
- Test standard Water permeability rate: DIN EN 1062-3
- Gloss level at 85º: Matt
- Test standard Gloss level: ISO 2813
PRODUCT PROPERTIES
- Mineral Matt
- Cradle to Cradle Certified -Certificate Silver
- C2C Certified Material Health
- Highly Permeable
- Microporous
- Hydrophilic Surface
- Hydroactive effect for non-toxic algae prevention
- Antistatic, Non-thermoplastic
- Absolutely Uv-resistant, Lightfast
- Fire behaviour: non-flammable (class a2-s1,d0 as per en 13501-1 acc. To classification report)
- No biocides added, no plasticisers added & no solvents added
APPLICATION INSTRUCTIONS
SUBSTRATE PREPARATION
The substrate must be dry, sound, free from chalking, clean and dust-free. Loose parts of existing coatings must be removed mechanically or by high-pressure water jetting. Defective areas must be filled and texture-matched using a suitable repair material. Any sintered layers on new renders must be removed with KEIM Ätzflüssigkeit (lime remover) according to instructions.
APPLICATION CONDITIONS
Ambient and substrate temperature ≥ 5 °C during application and drying. Do not apply in direct sunlight or on sun-heated substrates. Protect surfaces from direct sun, wind and rain during and after application.
PREPARATION OF MATERIAL
Stir up KEIM AquaROYAL-Color thoroughly before application.
APPLICATION
- KEIM AquaROYAL-Color can be painted, rolled or airless sprayed (nozzle: ≥ 435 ).
- Primer coat: KEIM AquaROYAL-Color always apply undiluted.
- Final coat: KEIM AquaROYAL-Color always apply undiluted.
DRYING TIME
Can be overcoated after 12 hours at the earliest (at 23°C and 50% RH). At higher relative humidity, layer thicknesses and/ or lower temperatures, drying is delayed accordingly.
CONSUMPTION
Approx. 0,5-1,0 kg/m² for two coatings. These material consumption values are guide values for smooth substrates. Exact consumption values must be determined by means of test areas.
CLEANING OF TOOLS
Clean immediately with water.