Egger COMPACT LAMINATE FLAMMEX CE
COMPACT LAMINATE FLAMMEX CE
COMPACT LAMINATE FLAMMEX CE
The compact laminates Flammex CE look the same as the compact laminates with a black core.
However, they are characterised by a significantly improved fire resistance and are classified as B-s2, d0 in accordance with EN 13501-1. With reduced ventilation, and substructure of low flammability or non-flammable substructure, the Flammex B CE compact laminates may even be classified and used as B-s1, d0.
INFORMATION
PRODUCT TYPE
Flammex Compact Laminate CE
USE
- Furniture
- Interior Design
DIMENSIONS
- Thickness range: 5, 6, 8. 10, 12 and 13 mm
- Standard size: 2,790 x 2,060 mm
- Maximum length: 5,600 mm
- Maximum width: 2.060 mm
APPLICATIONS
- Wall And Ceiling Claddings
- Trade Fair Construction
- Areas With Increased Fire Resistance Requirements
CHARACTERISTICS
- Low Flammability
- Medium Smoke Emission
- Low Heat Release
- No Flaming Droplets
COMPACT LAMINATE WITH PEARLESCENT DECOR
Pearlescent decors and therefore ACF compact laminates are identified with a special icon in the Collection. This icon stands for: "Only for vertical applications — pearlescent decor*. Compact laminates with pearlescent decor surfaces are produced with a single sided decorative effect. The non-pearlescent decor on the reverse acts as balancer.
CARE AND CLEANING RECOMMENDATIONS
Due to their resistant and hygienic, dense surfaces, EGGER Compact Laminates Flam mex CE do not require any special form of care. Generally, the surfaces are easy to clean. This also applies to textured surfaces.
For further information, please consult the leaflet "Cleaning and Maintenance Instructions".
This lee noir al clam shat hasOven carefully drawn up lo thcbm1 or our knowlcdfrc. Mcintonation paorksi is bosh co pear brat esPnnrot os well as innouse legs and Idled, our current slate of knewledge. His aended kw inloonatioi Only and does nol (aniline e a guatantee Intents d product popetles or Suaabilly for vecilc applitedon4. We steepno RBbiINy 6m eery mistake; ergots in vandal ds or pdnling enoes. In add Oka.
I ethnical modiliicaliocn tan resod from the cm inuous funlid deeelopmeni, as wdl as fen chutes in Odd ards and cbamtentS originating from slab/toy [cares. The eonients d t his tedlIkal data sheet should Mettle. elm be oonsid tied as instruthons Sot usece aslegaltitindine. Unless mhenslse slated. our Generd lensand Conditions apply.
PROCESSING
Compact laminate can be readily processed like other wood-based materials. Carbide metal tools are mainly used. Choosing diamond-tipped tools is recommended for large quantities and when machining centres are used. Despite the good dimensional stability of compact laminate. changes in the surrounding conditions may affect the board.
Format changes therefore have to be taken into account at the outset for processing and design. An expansion play of 2.0 mm per m should generally be allowed.Compact laminate Flammex can be mounted and installed Ina wide variety of ways and with the help of various non-combustible mounting systems. Special tested mounting systems may have to be installed depending on the use of the rooms.
The mounting systems and hardware have to be tailored to the area of application. Further information on storage and processing is found In the processing instructions "EGGER Compact Laminate".
ADVANTAGES
- Low flammability
- Moderate smouldering, non-dripping
- Resistant and durable
- Moisture-resistant
- Hygienic and easy-to-clean
- Resistant to liquid cleaning agents / chemicals
- Antibacterial surface property in accordance with ISO 22196 (=JIS Z 2801)
- Available in the coordinated set of matching decors with other EGGER products
FIRE BEHAVIOUR
- EGGER Compact Laminate Flammex CE meets the special requirements of EN 13501-1 in case of fire.
- According to EN 13501-1, the reaction to fire is classified as follows: B .
- The additional classification in regards to smoke development is:
- s2 The additional classification in regards to dripping / dropping while burning is: do
STORAGE
Compact laminate must be stored in enclosed and dry rooms, at approximately 18°C to 25°C and a relative humidity of approximately 50% to 65%. When the original packaging is removed, the compact laminate must be stored on horizontal, level and sturdy protective boards. Direct floor contact and/or exposure to the sun must be avoided In all cases. A laminated protective board (no raw chipboard) of at least the same format should be used to cover the top board.If horizontal storage is not possible, the compact laminate must be stored at an angle of approximately 80° against a full-surface support with counter-support. Using a laminated protective board of at least the same format Is required for upright storage as well.
QUALITY CHARACTERISTICS / TECHNICAL DATA
EGGER Compact Laminate Flammex CE is classified as CGF (Compact General-purpose Flame-retardant) according to EN 438-4. Compact laminate with full-surface pearlescent decors is classified according to EN 438-8 as type ACF (Pearlescent laminate Compact Flame-retardant).
| Property | Standard | Unit | value CU Rec 961 | value ACE Rec.966 |
|---|---|---|---|---|
| Resistancetosurfaceabrasion | EN 438.2:10 | Number of revolutions (per minute) Starting abrasion point | 150 | - |
| Shock resistance to a sphere with a large diameter | EN 438.2:21 | Drop height In mm 2mm sit< 6mm 6mmst Diameter of the impression In mm | 1,400 1,800 s 10 | 800 800 s 12 |
| Scratch resistance | EN 438.2:25 | Grade | 3 | 2 |
| Resistance to staininggroup 1 and 2 | EN 438.2:26 | Grade | 5 | 5 |
| Resistance to staining group 3 | EN 438.2:26 | Grade | 4 | 4 |
| Light fastness Xenon arc lamp (surface) • | EN 438.2:27 | Grey scale | 4 to 5 | 4 |
| Stress crack susceptibility | EN 438.2:24 | Grade | 4 | 4 |
| Levelness" | EN 438.2:9 | Depending on thickness In mm/m 2.0 mms t<6.0mm 6.0 mm s t<10.0 mm 10.0 mmst | 80 50 30 | 80 50 30 |
| Resistance to immersion In boiling water | EN 438.2:12 | Mass Increase in % tz 5mm Thickness Increase in % ta 5 mm Appearance in degrees Edge rating (min) | 20 20 4 3 | 30 60 4 3 |
| Dimensional stability at elevated temperatures | EN 438.2:17 | Cumulative dimension change In % t z 5 mm L •T‘i | 0.3 0.6 | 0.3 0.6 |
| Resistance to dry heat | EN 438.2:16 | Grade | 4 | - |
| Resistance towater vapour | EN 438.2:14 | Grade | 4 | 3 |
| Resistance to moist heat(100 °C) | EN 12721:2009 | Grade | 4 | - |
| Density | EN ISO 1183-1 1.35 | g/cm' a | z 1.35 | z 1.35 |
| Modulus of elasticity forbending | EN IS0178 | MPa | 9,000 | 9,000 |
| Bending strength | EN 150178 | MPa | 80 | 80 |
SURFACE FINISH ACCORDING TO EN 13722
| Surface | Gloss units | Maximum deviation |
|---|---|---|
| Gloss surface | > 70 | ± 15 GU |
| Semi gloss surface | 30 - 70 | ± 10 GU |
| Semi matt surface | 10 - 30 | ± 5 GU |
| Matt surface | <10 | ± 3 GU |
TOLERANCES
| Nominal thickness (mm) | Thickness tolerance (mini) | Length tolerance (mm) | Width tolerance (rim) |
|---|---|---|---|
| 5 and 6 | ±.40 | +10/•0 | +10/•0 |
| 8 and 10 | ±0.50 | +10/•0 | +10/•0 |
| 12 and 13 | ±0.6 | +10/•0 | +10/•0 |