Raynor Alumaview® Av200 Garage Door
ALUMAVIEW® AV200 GARAGE DOOR
ALUMAVIEW® AV175 GARAGE DOOR
Aluminum Sectional Rail and Stile Doors
Designed for peak performance and strength, this 2″ thick Raynor AlumaView AV200 aluminum sectional rail and stile door is available in larger sizes and features bold rail construction for maximum durability, reliability, and beauty. Build your door with ThermaXPS™ insulation for increased thermal performance.
FEATURES
AV175 FEATURES AND OPTIONS
Every Raynor AlumaView AV200 aluminum sectional rail and stile door is built for superior performance and includes the features listed below.
YEARS OF DURABILITY
AlumaView AV200 door sections are clear-anodized for maximum durability and are designed to withstand minimum wind loads of 20 p.s.f. Higher pressure ratings are available upon request.
DECREASED ENERGY COSTS
AlumaView doors help you reduce energy costs with a U-shaped, vinyl bottom weatherseal secured by a sturdy aluminum retainer.
CUSTOMIZED TRACK*
Track systems are supplied to fit special clearances, inclines, or contour applications. Hardware and track systems can be customized to fit any need. Additional trussing is available for special wind loading applications. A QuikClip™ pre-assembled track option is also available. *Some options may be limited to door size or model.
JAMB SEAL
EPDM rubber jamb seal also helps to reduce air infiltration and decrease energy costs by sealing the side of the AV200 door when closed.
ENDURACOTE™
The EnduraCote hardware system comes with springs, track, and hardware that are powder coated to provide a clean, finished look and maximum protection against rust.
ALUMINUM PANELS
For busy work environments and to prevent glass breakage, aluminum panels protect your investment. Choose from impact-resistant and insulated panels as well.
LOCKS
In applications where control and access are important, choose from a variety of locking options to help keep your building secure. Locks come in both inside and outside variations.
HEADER SEAL
A flexible vinyl flap header seal reduces air infiltration and energy costs by sealing the top of the AlumaView AV200 door against the header.
RUGGED HARDWARE AND SPRINGS
The AlumaView AV200 door comes packaged with the right combination of hardware, track, and springs to match your door’s size and application.
SNAP-IN RETAINER
AlumaView AV200 panels and glass are sealed and held in place with a snap-in retainer. Clear anodized, RAL9003, RAL 9016 and standard white doors use gray snap-ins. All other doors use black snap-ins.
CHOICE OF WINDOWS
For maximum design flexibility, choose from tempered, tinted, double-strength, insulated, acrylic, polycarbonate, or impact-resistant glass in a variety of thicknesses.
ANODIZED FINISHES
Choose from six custom anodize finishes including champagne, light bronze, medium bronze, dark bronze, extra dark bronze, or black.
ELEGANT FINISH WOODTONES™
Aluminum coated with durable and long-lasting material that delivers a high definition wood grain look.
CARBON MONOXIDE VENT
Allows you to channel fumes to the outside when the door is closed. Available in a variety of sizes.
SLEEKSIGHTLINE™
AlumaView AV200 and AV300 models offer a sleek 1-pane or trendy 2-pane glass layout. These new glass layouts are available now and vary depending on glass type and door size.
RAIL & STILE INSULATION
ThermaXPS™ insulation fills the AV200 rails and stiles to boast an R-value of 4.31**. This closed-cell insulation has minimal water absorption and prevents mold and mildew. Combine the ThermaXPS, along with our other energy-saving door features, and you will have a top-notch thermal solution. **10×10 door built with both double end stiles and ½” insulated Low-E Glass.
REMOVABLE CENTER POSTS
Carry-away, swing-up options available for extra-wide openings. Ideal for agricultural or airplane hangar applications.
HIGH-CYCLE COUNTERBALANCE SYSTEM
For reliable operation in high traffic areas, choose high-cycle torsion springs with 25,000, 50,000, or 100,000-cycle life. For reduced maintenance and ultra-smooth operation in heavy-use applications, choose a weight counterbalance system..
IECC REQUIREMENTS PACKAGE/CALIFORNIA TITLE 24
The International Energy Conservation Code (IECC) requires building components to meet minimum Air Infiltration rates. This option will ensure the AV300 and AV200 will exceed the latest IECC and Title 24 standards for air infiltration (only), by using the required header and jamb seals and track mounting. Exhaust ports and pass doors cannot be used.
PEDESTRIAN DOOR
Pedestrian doors are designed for convenient entry and to help minimize energy loss. *Some options may be limited to door size or model.
INFORMATION
BENEFITS
- Durable
- Rugged hardware and springs
- Reduced energy costs
TECHNICAL INFORMATION-PANEL SOLUTIONS
| Door Width | Number of Panels |
|---|---|
| Up to 9’2″ | 2 |
| 9′ 3″ – 12′ 2″ | 3 |
| 12′ 3″ – 16′ 2″ | 4 |
| 16′ 3″ – 20′ 2″ | 5 |
| 20′ 3″ – 24′ 2″ | 6 |
CHARACTERISTICS
- Durable
- Energy-saving
- Optional pedestrian door
- Lockable
- Choice of finishes
TECHNICAL INFORMATION-SECTION SOLUTIONS
| Door Width | Number of Sections |
|---|---|
| Up to 8’2″ | 4 |
| 8′ 3″ – 10′ 6″ | 5 |
| 10′ 7″ – 12′ 6″ | 6 |
| 12′ 7″ – 14′ 6″ | 7 |
| 14′ 7″ – 16′ 6″ | 8 |
GUARANTEE
Limited Warranty: Sections: 5-Years, hardware: 1-Year, springs: 1-Year
DOOR
- Model : AlumaView AV200
- Size : 24′ x 24′ Max
- Operation : Manual, Motor or Hand Chain
- IECC Thermal Performance : Tested U-Factor 0.72 (w/ insulated, Low E glass), Tested U-Factor 0.76 (w/ insulated, clear glass), Tested U-Factor 1.10 (w/ DSB glass)
TRACK
- Finish : Galvanized or Optional White Powder Coat
- Size : 2″ or 3″
- Gauge : 13 and 16-Gauge
- Type :Normal Headroom, Rear Mount Low Headroom, Front Mount Low Headroom, Lift Clearance, Vertical Lift, Incline, Contour, and QuikClip™ Pre-Assembled Track Options
COUNTERBALANCE SYSTEM
- Type : Torsion Spring, Tandem Shaft Torsion Spring, or Weight Counterbalance
- Shafts : Tube or Solid (D-Shaft, 1″ Keyed, 1-1/4″ Keyed)
- Springs : Spring Inner Diameter: Spring Inner Diameter: 2-1/4″, 3-1/2″ or 5-1/2″; Duplex or High Cycle (30K, 50K, 100K); Optional Black Powder Coat
APPLICATIONS
- Large opening
- Showrooms
- Automotive
- Retail
- Restaurant
HARDWARE/ACCESSORIES
- Hinges : 11, 13, 14-Gauge or Hybrid
- Rollers : Standard (2″ or 3″) or Heavy Duty (2″ or 3″)
- Finish : Galvanized or Optional White Powder Coat
- Lock : Interior Slide Lock or Exterior Lock Bars
- Seal(s) : Jamb Seal
- Pedestrian Door : 32″ Wide x 3 Sections High
- Optional Wind Loading : Certified Wind Load Available
- Hanger Angle : 11, 13-Gauge Galvanized or 13-Gauge White Powder Coated
SECTIONS
- Material : Aluminum
- Surface Texture : Smooth
- Section Thickness : 2″
- Gauge : N/A
- Section Joint : Tongue-in-Groove
- Rail & Stile Insulation : ThermaXP
- Stiles : Extruded aluminum(mini .05″)
- Construction : Rail & Stile – minimum .05″; 5/16″ diameter screws
- Seals : Bottom Seal (3″, 4″ Gray; 3″ Yellow; or 3″ Black EPDM), Optional Header Seal. Optional IECC and California Title 24 air filtration compliant package available.
- Panel Configuration : .50″ thick Aluminum panels
- Trussing : Wind Load: 20 P.S.F. Tested/13.3 P.S.F. Design Load (standard); Material: U-bar (18-Gauge or 20-Gauge);Sizes: 4″, 6″, or 8″
- Color : Clear and Optional Anodized Finishes, ArmorBrite Powder Coat System, or Elegant Finish Woodtones
- Windows : 1/8″ DSB Glass; 1/8″ 1/4″ 3/16″ Clear Tempered Glass; 1/8″ 1/4″ Tinted or Tinted Tempered Glass; 3/16″ 1/4″ Clear Glass; 1/4″ Clear Laminated Glass; 1/4″ Clear Wire Glass; 1/2″ Insulated DSB Glass
SPECS/DRAWINGS
STANDARD DRAWINGS - 2-INCH TRACK/BRACKET-MOUNTED
| Sheets | Drawings | |
|---|---|---|
| Normal Headroom | DWG Drawing | |
| Lift Clearance | DWG Drawing | |
| Vertical Lift | DWG Drawing | |
| Low Headroom Front-Mount | DWG Drawing | |
| Low Headroom Rear-Mount | DWG Drawing |
STANDARD DRAWINGS - 2-INCH TRACK/ANGLE-MOUNTED
| Sheets | Drawings | |
|---|---|---|
| Normal Headroom | DWG Drawing | |
| Lift Clearance | DWG Drawing | |
| Vertical Lift | DWG Drawing | |
| Low Headroom Front-Mount | DWG Drawing | |
| Low Headroom Rear-Mount | DWG Drawing |
STANDARD DRWAINGS - 3-INCH TRACK/ANGLE-MOUNTED
| Sheets | Drawings | |
|---|---|---|
| Normal Headroom | DWG Drawing | |
| Lift Clearance | DWG Drawing | |
| Vertical Lift | DWG Drawing | |
| Low Headroom Front-Mount | DWG Drawing | |
| Low Headroom Rear-Mount | DWG Drawing |
COLORS
ELEGANT FINISH WOODTONES™ OPTIONS
-Aged Dark Oak -American Douglas -American Maple -Cherry -Cherry Flame -Colony Maple -Dark Walnut -European Cherry -Golden Oak -Knotty Pine -National Walnut -Oak -Oregon Douglas -Table Cherry -Teak
ANODIZED FINISH OPTIONS
-Clear -Champagne -Light Bronze -Medium Bronze -Dark Bronze -Extra Dark Bronze -Black
ARMORBRITE™ POWDER COAT SYSTEM
Custom Colors: ArmorBrite: 188 custom powder coated colors available.
