Watco Chemi-Coat Anti-Slip Paint Coating
CHEMI-COAT ANTI-SLIP PAINT COATING
CHEMI-COAT ANTI-SLIP PAINT COATING
Chemi-Coat® Anti-Slip is a one coat high build epoxy resin coating which offers excellent durability, chemical resistance and slip-resistance.
Provides a glossy, hygienic and easily cleaned textured surface. A single coat is usually sufficient. Very porous surfaces should be treated first with 4 Hour Epoxy Primer.
INFORMATION
BRAND
Watco
PRODUCT TYPE
Paint Coating
RECOMMENDED NUMBER OF COATS
1
PRIMER REQUIRED
Yes, on very porous surfaces. Use 4 Hour Epoxy Primer.
COATING
Discoloration may occur with some chemicals. This is not necessarily an indication of degradation of the coating. For added chemical resistance, particularly to stronger acids, please refer to Watco Chemi-Coat Acid Strength.
FINISH
- Glossy
- Textured
PRODUCTION
Made in United States
AVAILABLE COLORS
8
SUITABLE FOR
- Concrete
- Some Metals
- Well-bonded Paint
USE
Wall & Floor
SOLVENT
Low Solvent Content
DETAIL
- Excellent resistance to many aggressive chemicals
- Suitable for a variety of floor and wall surfaces
- Ideal for areas where chemical spillage or heavy wear occur
- Added coarse aluminum oxide grit for maximum grip wear and resistance
- Approved for use on sand and cement screed or concrete with underfloor heating systems (up to 85°F surface temperature)
COLORS
- Black
- Navy Gray
- Silver Gray
- Tile Red
- Safety Yellow
- Mid Blue
- Mid Green
- Dark Gray
CURING TIME (HOURS)
16 Hours in 70°F
USAGE INTERIOR/EXTERIOR
Interior
DOWNLOADS
↓ Tds Chemi-coat Anti-slip.pdfpdf
↓ Sds C11402188 Chemi-coat-anti-slip-black.pdf
↓ Sds C11404193 Chemi-coat Anti-slip - Navy Gray Kit.pdf
↓ Sds C11405190 Chemi-coat-anti-slip-silver-gray.pdf
↓ Sds C11408196 Chemi-coat Anti-slip - Tile Red Kit.pdf
↓ Sds C11415195 Chemi-coat Anti-slip - Safety Yellow Kit.pdf
↓ Sds C11438191 Chemi-coat Anti-slip - Mid Blue Kit.pdf
↓ Sds C11439192 Chemi-coat Anti-slip - Mid Green Kit.pdf
↓ Sds C14403189 Chemi-coat Anti-slip -dark Gray Kit.pdf
HOW TO APPLY
SURFACE PREPARATION : CONCRETE AND BRICK
Concrete to be treated must be dry, at least four weeks old and free of any soft surface laitance, contaminants, and not subject to rising damp.
All loose material should be removed. Very smooth bare concrete or concrete with soft surface laitance should be etched with Watco Cemtetch and the area thoroughly hosed off and allowed to dry. Grease or oil should be removed with Watco Bio-D (or a similar degreaser) and the area thoroughly hosed off and allowed to dry. Very smooth previously painted surfaces should preferably be abraded to improve adhesion.
SURFACE PREPARATION : STEEL
Remove loose or flaking material, rust and any previous coatings by wire brushing or disc grinding to achieve a bright surface. Oil or grease should be removed with Watco Bio-D and the metal then washed with Water and allowed to dry. The coating should be carried out immediately providing flash rusting has not occurred.
MIXING
- Each Chemi-Coat pack consists of a container of curing agent and a container of resin. The curing agent and resin must be thoroughly mixed together with a paint mixer attached to an electric drill until an even color is obtained.
- Important : Once the contents of the pack have been mixed a chemical reaction takes place which causes a rise in temperature and speeds up the curing of the product.
APPLICATION
If appearance is critical we recommend the application of a small trial area first. Best results are obtained in warm conditions. On horizontal surfaces apply with a medium, pile type roller (not foam) in one coat. On vertical surfaces, two thin coats are recommended. The second coat should be applied within 24 hours.
